Enclosure housing design jobs

I’m looking for a 3D modeler who can translate my concept into a print-ready STL: a butterfly-shaped jewelry box that keeps its proportions elegant while housing at least eight fully functioning drawers. The finished piece must measure exactly 12" wide, 12" tall and 3.5" deep, and the overall silhouette should read as a realistic butterfly rather than an abstract or cartoon interpretation. I plan to print the box in PETG, so please design with typical FDM constraints in mind—wall thicknesses that won’t warp, sensible overhang angles, and parts that can be assembled cleanly after printing. Fit and tolerance around the drawers are critical; they need to slide smoothly but stay aligned once the box is upright. Deliverables • One complete S...

...wiring diagram 2. Building EMG display software for Windows • Real-time data visualization (raw signal and RMS/average) • Session recording to CSV or similar format for later analysis • A user-friendly interface designed for clinicians with minimal technical training • Installer, full source code, and brief user manual 3. Other minor modifications • Tidy PCB layout and enclosure fit • Basic documentation so the device package is ready for ethics approval/IRB review Preferred tools are open to you (C#/WPF, Python + PyQt, or C++/Qt are all fine) as long as the final executable runs on Windows 10 without admin rights. Acceptance criteria • Vibration feedback latency < 50 ms and repeatable across 100 trials &...

Off-market Florida housing deal sourcing I’m looking for help finding property investment opportunities in Florida where I can convert pre-existing motels (or other suitable buildings) into 1-bedroom apartments for affordable living, and also identify land opportunities to build from scratch. The goal is affordable housing for low income workers across the Tampa–Orlando–Melbourne corridor, in areas with strong rental demand. Scope of work - Source off-market property opportunities in Florida suitable for conversion to 1-bedroom apartments (including pre-existing motels and old sites/office buildings that could be converted). - Source land opportunities in Florida that could support new-build affordable housing targeting low income workers in the T...

...software hooks are a bonus. • Mechanical design: compact housing that can be ceiling-mounted or set on a cart, with straightforward lens shift or keystone correction to hit a wide classroom screen. • Documentation & files: CAD drawings, BOM with sourcing links, wiring diagrams, and a step-by-step guide that a school tech team could follow to assemble or maintain the unit. • Prototype validation: short video or live demo proving touch accuracy, response time, and image uniformity. While the must-have is interactive touch, I’m open to recommendations on optional extras—wireless connectivity or even a 4 K optical block—so feel free to flag those if they strengthen the overall design. I’ll review progress in logical mil...

...diesel generator canopy whose main function is soundproofing. The enclosure will be built entirely from steel, so every detail—from structural members and weld symbols to the arrangement of acoustic panels and ventilation louvers—has to reflect that choice of material. My goal is to hand your package straight to the fabricator without additional rework. That means: • Fully dimensioned 2D shop drawings in DWG and PDF • A concise bill of materials with steel grades and thicknesses • Section views showing acoustic lining, doors, hinges, lifting eyes, cable-entry plates and exhaust routing • Notes on surface treatment, fasteners and gasket specifications • A 3D model (STEP or similar) for quick visual checks • Up to two design...

PCB and 3D Enclosure Expert Needed We are looking for an experienced PCB designer who can also create a compact 3D-printed enclosure. We already have an ESP32-based PCB with Ethernet and Modbus/RS485. The schematic, PCB layout and BOM are available, but we need a new expert to: Review the schematic and PCB layout Correct any errors or necessary improvements Verify that all components are available for JLCPCB assembly Prepare a complete, production-ready JLCPCB package Design a small enclosure suitable for JLCPCB 3D printing Deliver all editable source files, Gerbers, BOM, CPL, STEP and STL files The final package must be ready for us to upload and order directly from JLCPCB. We estimate approximately two days of work. Please send your fixed price, estimated...

We are looking for an experienced Mobile App Developer (Android/IOs) / Development Team to design and develop a complete Society Management Application for ZipXpress Technologies Pvt. Ltd. The platform will be a multi-society SaaS solution that allows multiple housing societies/apartment communities to manage residents, owners, tenants, maintenance collections, vendors, complaints, visitors, notices, amenities, payments, and society operations from one platform. The system should include Mobile Apps for Residents/Society Users, Society Admin Dashboard, Vendor Module, Security/Guard Module, and a Super Admin Dashboard for managing multiple societies

Research, create, and design an enclosure for an Underwater Scanning Sonar System. The project will include a bracket for XY dual stepper motors, a motor controller, a Raspberry Pi, and a sonar transducer with a PCB. Heatsink, Battery, and Mounting Base. Other parts or configuration to be determined at a later time in the project.

We are looking for an experienced B2B LinkedIn-focused content agency or freelancer to help us build the digital presence of our company, Jalsenx – Intelligent Water Technologies. Jalsenx provides water-saving solutions for hotels, hospitals, housing societies and commercial properties. We have real client projects, water-saving data, ROI analyses, installation photos and will be collecting customer testimonials and project videos. Our Requirement Our primary focus is LinkedIn, followed by Instagram. We need a partner who can convert our existing project material into high-quality B2B content, including: LinkedIn posts and thought-leadership content Client success stories and case studies Data-driven/carousel posts Graphics and creatives Editing of raw project and testim...

ICP: Windows & Doors Installers (UK) — Database Reactivation Core definition Owner-operated retail window and door installation companies selling directly to homeowners, trading 5+ years, . Firmographics Location: England, Wales, Scotland. Weight toward the North West, Yorkshire, West Midlands, East Midlands and the South East — older housing stock, high replacement volume. Headcount: 10–60. Sweet spot 15–40. Revenue: £2M–£15M. Years trading: 5+ minimum, 8+ ideal. Sells directly to the homeowner. Not a fabricator, not trade-only supply. Decision maker Owner or Managing Director under 40 staff. Above that, Sales Director or Marketing Manager, but the owner still signs. Disqualifiers Under 3 years trading. Two- and three-man fitting outfi...

...Gerbers and a concise BOM with readily available parts. • Firmware built with ESP-IDF or Arduino-ESP32 that can send and receive short text payloads over Wi-Fi, display them (even a simple OLED/LED matrix is fine), and confirm delivery. • Low-power strategy outlined and demonstrated so the device can idle for weeks on a fresh battery yet wake instantly for message activity. • A 3-D printable enclosure file that shows how everything is secured inside the correction-tape-sized shell. Deliver the compiled binary, source code, and a quick start read-me so I can flash, assemble, and begin field testing without hunting for settings. I will judge the work on physical fit, stable Wi-Fi performance, clean code that I can extend, and practical battery life. If this s...

I have a consumer-electronics concept ready for the next step and need a clean, production-ready double-layer PCB layou... concept ready for the next step and need a clean, production-ready double-layer PCB layout. The board will host a mix of through-hole and surface-mount parts, so component placement and routing must accommodate both styles without ballooning the footprint. Deliverables: • Finished design files in Altium and industry-standard Gerbers • Drill files, pick-and-place data, and a tidy BOM (Excel or CSV) • Test PCB's with assembly I will review the Gerbers in ViewMate and run a quick fit-check in our enclosure CAD; the project is complete once the files import cleanly and the report answers all open questions. Looking for someone in I...

I’d like to turn the two pergola-covered side passages of my home into functional spaces. On the left-hand side the goal is a secure outdoor cat enclosure. I want the existing pergola posts and roof retained; you’ll wrap the sides in strong mesh so the cats can see out yet stay protected. The concrete slab that’s already there remains as the floor, so no extra groundwork is required. Inside, please build in a few fixed climbing platforms and a cosy sleeping nook that can handle the weather. The right-hand side will become a simple, lockable storage shed. Again, keep the current pergola frame but enclose it with durable, weather-resistant panels, add a solid door, and fit basic shelving so boxes and garden tools stay dry and organised. I’m after a clean, pr...

I’m developing a dedicated handheld that will operate offline. No Wi-Fi, Bluetooth, cellular, or any other radio is required, so the entire design has to function in isolation. Because of that restriction I’m open to whichever operating system keeps the footprint light and the boot time quick, whether that’s a stripped-down Android build with networking stacks removed or a fully custom OS. but more likely just on/off. then a button to run. Your task is to take the idea from concept to a working prototype. I’ll need the electronic design (schematic, PCB layout, and component selection), a daylight-readable display, a rechargeable battery able to power at least eight hours of continuous use.. Low power consumption, immediate on/off and rock-solid stabil...

We are looking for an experienced Mechanical/Industrial Engineer specialized in SolidWorks or similar CAD software to design a reusable steel mold for the mass production of precast concrete housing modules. The concrete module is approximately 3.0 m wide × 7.0 m long × 3.0 m high, open at the top, with an additional 1.2 m balcony on the front side. Main concrete specifications: * Wall thickness: 80 mm * Floor thickness: 200 mm * 4 concrete walls + floor cast as one monolithic piece * No roof during this casting process We need the complete manufacturing design of the steel mold, including: * External steel formwork * Internal negative/core mold * Steel plate thickness calculation * Structural frames and reinforcement ribs * Corners, connections and lo...

...input and automatic power-down logic to protect the battery Scope of work 1. Component selection: image sensors, SoC/MCU (ARM, RISC-V, or similar), 4G modem, GPS, IMU, power management, and thermal considerations. 2. Custom PCB design and layout, followed by manufacturing files ready for a quick-turn proto run. 3. Low-level firmware to handle sensor pipelines, H.264/H.265 encoding, LTE networking, GNSS, SD-card file management, and event-based recording (FreeRTOS or bare-metal is acceptable). 4. Assembly of at least one fully functional prototype with enclosure recommendations. 5. Bench and in-vehicle tests validating video quality, streaming stability, GPS accuracy, and motion/impact triggers. Deliverables • Complete schematics, BOM, and Gerber/ODB++ fi...

I want to have a replacement cover for my vehicle’s tail light professionally modeled so I can print it on my own 3-D printer. The final deliverable must be an OBJ file that is completely watertight and print-ready. I already sketched the co...as the exported OBJ adheres to standard 3-D-printing conventions (manifold geometry, no reversed normals, real-world scale in millimetres). Deliverables • One OBJ file ready for slicing • A couple of rendered screenshots to confirm shape and mounting details • If small tweaks are needed after a test print, one revision is included Acceptance criteria: the model must seat flush on the lamp housing, all fastener locations align, and the cover prints without mesh errors. Looking forward to collaborating and getting th...

...3D CAD Files: Clean, manifold meshes and parametric models provided in .STEP, .STL, and .F3D formats. Component Housing: Internal structural mounts designed specifically for a mini-ITX motherboard, SFX power supply, low-profile CPU cooler, and a compact GPU. Assembly Design: Split-shell architecture featuring snap-fit or hidden screw fasteners to facilitate easy manufacturing and desktop assembly. Aesthetic Detailing: Integrated ventilation mesh patterns, a dedicated cutout for an external power switch, and optional mounting points for RGB lighting rings. Ideal Freelancer Skills Advanced proficiency in Fusion 360, SolidWorks, or Blender. Proven experience in PC case design, thermal airflow optimization, and 3D printing tolerances. Ability to deliver print-rea...

...program, campaign priorities, public events, office/contact information, frequently asked questions, and other non-sensitive information that they want citizens to receive. For example, a citizen could call or message the AI and ask: * What is the party's political program? * What are the main priorities of the candidate? * What does the party propose regarding employment, education, healthcare, housing, infrastructure, or other public issues? * Where and when is a campaign event taking place? * How can I contact the local campaign office? * What are the official campaign activities and announcements? * Can you explain this point from the party's program? The AI should answer **only from the information approved and provided by the client**, communicate naturally in ...

PCB Design & Engineering for HydroNest RO Plant Controller 1. Project Objective We are developing a professional controller PCB for commercial/light-commercial RO water treatment plants under HydroNest India. The objective is to take our existing functional requirements, selected components/modules and control logic, and have an experienced electronics engineer design, optimize and finalize the complete electronic controller. We are not looking only for PCB layout work. The engineer should be capable of taking the requirements at a system level and developing the complete electrical design, schematic, component selection/optimization and production-ready PCB. ⸻ 2. What We Will Provide We will provide: * RO plant operating requirements and sequence * List of...

...activities, vehicles, custom interiors, donation packages, progression, and the small immersive features that make the city stand out. The server should feel like a real Detroit city, with real roads, neighborhoods, landmarks, RiverWalk, transit, dispensaries, and player-owned businesses. focus on the key systems you mentioned -- gang/block loyalty, trapping with peds, realistic crimes, tiered housing and trap interiors, detailed PD/EMS roles, donation-based content, and strong server optimization so graphics packs run smoothly The goal will be to capture the depth and quality you like from YBN Chiraq while making the server original, Detroit-focused, and stronger technically. build real-brand-inspired dealerships for SRT/Dodge, Cadillac, Ford, etc., and replace Los Santos Cu...

Project Overview: We have a completed engineering design, schematics, and a preliminary Bill of Materials (BOM), along with a 3D STEP mechanical model for a portable electronic thermal device. We are looking for an expert PCB design engineer to prepare and deliver a complete Manufacturing Package ready for immediate submission to major PCB manufacturers (such as PCBWay / JLCPCB) without any errors. Main Tasks & Deliverables: Review the design and BOM, and propose the optimal PCB technical specifications (such as copper thickness, FR-4 TG thermal rating, and surface finish) based on the device's power and heating circuitry requirements. Gerber Files: Standard RS-274X format for all layers. Excellon Drill Files: Accurate drill and hole specifications. Pick-...

...containment, not trick teaching or general exercise. When a pet approaches or crosses a virtual or physical boundary, the unit should deliver a very mild shock stimulation—strong enough to deter, yet well within accepted animal-safety standards. Here is what I’m looking for: • A complete concept and schematic for the device, including sensor choice, power requirements, safety circuitry, and enclosure design. • Firmware or control logic that triggers the mild stimulus reliably and only when intended. • A brief user-setup guide so anyone can define or adjust boundaries indoors. If you can add optional sound or light cues as secondary warnings before the stimulus, that’s a plus, but the core requirement is the safe, adjustable shock out...

I'm looking for a skilled designer to create a minimalist, waterproof enclosure. The enclosure will house a solar panel on the top side and some antennas on the bottom side. Key requirements: - Minimalist design approach - Waterproof functionality - Securely house solar panel and antennas - Material: Plastic Ideal skills and experience: - Experience in designing waterproof enclosures - Strong understanding of minimalist design principles - Proficiency in working with plastic materials - Background in solar panel and antenna housing solutions Please provide samples of previous similar work.

I need a redesign of the existing SCND STL into a 5-part enclosure: Requirements: - Parts: Top shell, bottom shell, internal tray, Ø27 mm MagSafe holder, and switch button. - Maintain outer design. - Add USB-C and switch cutouts on both top and bottom shells. - Include alignment and assembly features using screws. - Final thickness of 6.5 mm. - Matte finish preferred. Ideal Skills and Experience: - Proficiency in 3D modeling and design - Experience with enclosure design - Familiarity with USB-C and switch integration - Strong attention to detail and precision

...Custom Wall-Mount Enclosure Design for Arduino UNO Q 4GB I am looking for an experienced mechanical/CAD designer to create a production-ready custom electronics enclosure for a commercial monitoring product called the PeafowlPro Hub. The initial Hub will be built around an Arduino UNO Q 4GB and will not include a display or additional internal expansion boards. The goal is a compact, clean, professional enclosure suitable initially for FDM 3D printing, while keeping the design practical for future manufacturing. Design Requirements The enclosure should be a white, two-piece design consisting of a front/top cover and rear/base housing. A snap-fit assembly is preferred, although the designer may recommend a better servicea...

Hi Tarek, For projects at this stage I normally begin with a short engineering phase before committing anything to schematic or PCB layout. The reason is simple: eventually every assumption has to answer to evidence. The product has to prove itself on the bench. It has to prove that the power architecture behaves as intended, that the radio still works once everything is squeezed into an enclosure, that the interfaces tolerate the environment they are connected to, and that the safety, EMC and regulatory requirements are accounted for before they became expensive problems later. Hardware becomes costly when an assumption survives long enough to be mistaken for a fact. Phase 1 is therefore about establishing what we actually know, what we still assume, what remains unknown, and ...

# NFC Design Requirements ## 1. Basic Requirements * **NFC Frequency:** 13.56 MHz * **NFC IC Supply:** 3.3 V * **NFC IC:** NXP NFC IC * **Host MCU:** ESP32 / selected MCU * **Communication:** I²C * **Antenna:** PCB loop antenna * **Target NFC Range:** 20–30 mm * **PCB:** 2-layer PCB preferred * **Operating Temperature:** -20°C to +70°C ## 2. NFC Antenna * PCB antenna shall be designed for **13.56 MHz**. * Antenna dimensions shall be optimized based on available PCB space. * Keep ground copper away from the antenna area. * Keep battery and other metal objects away from the antenna where possible. * Antenna matching components shall be provided for tuning. ## 3. Power * NFC IC supply: **3.3 V** * Provide local decoupling capacitors near the NFC IC. * NFC suppl...

...will be provided) in KiCad or EasyEDA — your call, please confirm. Select correct footprints for all parts, including the MLX90614 TO-46 can and the exact Waveshare LCD module connector (I'll provide the datasheet/part link). Route all traces, run DRC, and add mounting holes suitable for a small enclosure. Deliver Gerber files, BOM, pick-and-place file (for SMD assembly via JLCPCB/PCBWay), and the native KiCad/EasyEDA project files. Optional: basic enclosure clearance check (I'll share rough enclosure dimensions if needed). Deliverables: Schematic file (.kicad_sch or EasyEDA project) PCB layout file (.kicad_pcb or EasyEDA project) Gerbers + drill files, ready for fab BOM with SMD part numbers (JLCPCB/LCSC preferred for easy sourcing) Pick-and-place...

I’m building a compact IoT board that can collect sensor data, push it wirelessly to the cloud, and drive simple actuators—all on one reliable PCB. At the heart of the design I need a low-power microcontroller paired with the necessary sensors; wireless connectivity (Wi-Fi, Bluetooth or whichever protocol you recommend) will complete the link to the outside world. Here’s what I expect you to deliver: • Schematic and PCB layout files (Altium, KiCad, or similar) • Optimised BoM with readily available parts • Gerbers, pick-and-place, and fabrication notes • Basic firmware pin-map to confirm that the microcontroller, sensors, and control lines are correctly routed Please send a concise but detailed project proposal that shows how you&rsquo...

...heater, timer module, and enclosure parts I’d like to use (all stocked by major suppliers) What I need back: • A fully assembled, bench-tested prototype that runs for at least one hour without overheating • Basic performance notes: measured airflow (CFM), surface temperature at the heat outlet, and any assembly tweaks you made • Photos or short video showing the unit in operation I’m in Southern California, so local pickup or drop-off is ideal, but I can ship parts to a remote builder if you share progress photos and a final demo clip before shipment. Please quote for labor and any incidental hardware you expect to add; I’ll purchase the main components directly. If you’ve built small appliances, lab rigs, or DIY electronics with safe...

...drinks upright while the buggy bounces along. Experience with gimbal-style mechanisms is essential because the design must allow the cup to self-level on uneven terrain. Key requirements • Universal attachment: the holder should clamp securely to a wide range of frame diameters without tools. premium design to match the holder and ease of installation • Optional insulation cavity: if feasible, include a removable sleeve or double-wall concept to help maintain temperature - uncertain of this due to look and size of overall item • Materials: explore a primary structure in lightweight metal, soft-touch inserts or flex points in silicone, and durable plastic for the main housing. I’m open to your guidance on wall thicknesses, over-moulding and ...

...named Piphex from supplied reference images. This assignment is for exterior design and clean part separation only; I will complete the internal electronics engineering afterward. Match the reference closely from front, side, rear and three-quarter views. Target envelope is approximately 160 mm wide x 155 mm deep x 210 mm tall while preserving approved proportions. Use a hollow main shell with approximately 3 mm walls. Create separate solid bodies for the blue shell, black front face panel, black side vents/details, two eye lenses, mouth lens, forehead camera bezel and removable rear service door. Include an open neck passage. Use only functional seams between separate parts, with no decorative fake seams. Design for PETG FDM printing on a Bambu Lab P1S with a 256 mm build...

Hi, I am looking for an experienced CAD / product design engineer to professionally redesign and finalize an existing 3D model of a compact automated device. I already have a basic STL model that shows the general shape, size and layout I want. The current model should be used mainly as a visual and dimensional reference, but the final design must be properly engineered and fully functional. Approximate overall dimensions: 500 × 480 × 400 mm The final design needs to include: * A large open working area in the front, approximately 450 mm wide and at least 350 mm deep * A drainage surface and water collection tray underneath * A removable wastewater tank/drawer at the lower front, approximately 10–12 litres * The wastewater drawer must slide compl...

...legal file, location maps and pricing sheets so you can speak to prospects with confidence. I need someone already comfortable with real-estate sales—ideally you’ve handled plot or apartment transactions before and can guide buyers from first inquiry right through to registration. My preferred lead-generation channel is in-person networking events; if you have a strong local network of investors, housing-society contacts or developer relationships, that’s exactly what will help here. Of course, how you supplement that—online ads, referrals, even the occasional cold call—is up to you as long as the deals close. Key expectations and milestones • Source genuine buyers, primarily through networking events in and around Mumbai. • Conduct sit...

...interaction: one-button arming, LED/buzzer status feedback, and an easy way to send or display its current coordinates Deliverables 1. Full hardware design (schematic, PCB files, BOM) and enclosure model showing the integrated magnet system 2. Firmware source code that handles GPS acquisition, power management, and the chosen communication method (e.g., GSM SMS or GPRS) 3. Assembly and usage guide so I can reproduce, install, and test the device on my own vehicles 4. A brief field-test report proving reliable tracking accuracy and magnetic retention under normal driving conditions If you have experience with low-power embedded design, GNSS modules, and ruggedized enclosures, I’d like to see how you can turn this concept into a ready-to-deploy tra...

I already have a complete SolidWorks model of a small inverter enclosure; it just needs a quick touch-up to its ventilation design. I will send you a short guideline document that spells out the airflow clearances and grille pattern I want, so you can adjust only those features—nothing else on the housing should move. Once the tweaks are in place, I need the updated SolidWorks part/assembly, plus clean exports: • PDF and JPG views for a simple review set • DWG or DXF so I can archive the drawing in AutoCAD That’s the whole job. If you’re comfortable jumping into an existing SolidWorks file, following the provided ventilation spec, and pushing out those three file types, this should be a very fast turnaround.

I need a clean, rectangular enclosure model that I can drop straight into Bambu Studio and hit print. Inside, the housing must include accurate mounting bosses or standoffs for three elements: a 4" LCD, a GPS/9-axis sensor board, and a Raspberry Pi 4B. Please reference the official Raspberry Pi 4B and common 4" SPI LCD footprints so everything lines up without shimming. External requirements are simple: keep the overall shape rectangular and incorporate ventilation slots to help the Pi breathe; all other ports can stay sealed for now. Snap-fit or screw-together construction is fine as long as the lid can be removed without stressing the print. Deliverables • Ready-to-print 3MF or STL tailored for Bambu Lab printers • Source CAD file (Fusion 360, Soli...

...and a confident mature voiceover. Emphasize that the certification process is quick and easy and that The Certification Company can support management companies with in-house compliance departments. SCENE 1 — THE PROBLEM Timing: 0:00–0:05 Voiceover: “Failed inspections, housing violations, and subsidy interruptions can create major challenges for property owners.” Visual: Property owner or management professional reviewing inspection notices, violation documents, and agency correspondence at a desk. On-screen text: HOUSING VIOLATIONS? SCENE 2 — CERTIFICATION MATTERS Timing: 0:05–0:10 Voiceover: “Correcting a violation is only part of the process. Proper certification is what closes the matter with the agency.” Visual: Violati...

...booking system design considerations, hardware requirements as well as training and setup guidance (I will build the hardware myself and learn and understand the software design). A smooth pipeline—speech-to-text, intent recognition, response generation, and text-to-speech—is essential; you’re free to choose the stack (e.g., Whisper, Vosk, local LLMs, Rasa, Piper-TTS, etc.) so long as everything runs offline on both Windows and Linux. Deliverables • Source code and install scripts for the complete local stack • An easy way for me to add or edit FAQs and booking rules • Demonstration of the system running on a Windows workstation and a Linux SBC/VM, showing it can field the inquiries above and book an appointment successfully ...

MUST BE WILLING TO START TODAY. A bunch of websites and web apps deployed, immediately on a live server with someone who is willing to work for an extremely reasonable rate in exchange for recognition, a strong portfolio, recommendations, contact with key insiders, an apprenticeship at a major tech company with housing paid for.

...finished with easy-care vinyl or linoleum flooring, then guide them seamlessly into a private treatment room built for massages, seaweed wraps and other wet services. Layout needs • Front section: a compact relaxation / reception area furnished with comfortable chairs and ottomans plus discreet storage for retail items and linens. • Mid-coach: existing toilet stays; opposite it I want a shower enclosure suitable for wrap treatments, with proper waterproofing and drainage. • Rear section: dedicated massage room that accommodates a full-size table, towel warmer, storage cabinetry and dimmable lighting. What I expect from you • Two or more space-planning options showing precise dimensions and traffic flow. • Mood boards and material palette that ...

MISSION TITLE PCB design / layout for a DIY solar tracker (ESP32 mainboard) PROJECT DESCRIPTION I'm developing a solar tracker (2-axis, azimuth + tilt) controlled by an ESP32, with a touch TFT screen, SD card, RTC, angle sensors, control of 2 DC motors (azimuth/tilt), management of 48V/24V power rails, and various sensors (wind, LDR, battery voltage, temperature, gyroscope). The firmware is already developed and functional (Arduino/ESP32 code). A KiCad library of the modules used has already been prepared (schematics + footprints + 3D renders per module). The full GPIO/I2C mapping is documented and ready to share. I'm looking for a freelancer to design the complete electronic schematic and route the PCB (main board, built around the ESP32), based on the material...

...self-propelled dealer button that can glide across a felt poker table, light up in vibrant patterns, talk to surrounding hardware, and report its own movements. To make that happen I need a complete hardware package—schematics and a production-ready circular PCB—centered on the ESP32. Core requirements • Shape: round, “dealer button” footprint, slim enough to roll smoothly on felt while housing a lithium battery and two low-profile drive wheels. • Processor: ESP32 for built-in WiFi and Bluetooth; all I/O for motor driver, LED ring, sensors, and battery management must be broken out. • Connectivity: Both WiFi and Bluetooth should run concurrently without external modules. • Functions to support: lighting up with LEDs, comm...

I need a functional orange juice vending machine that operates without a payment interface. It will be placed indoors, such as in offices or malls. The final design should be 3D printable and compatible with CNC manufacturing Key Requirements: - Machine should extract juice from fresh oranges - No payment processing needed - Suitable for indoor placement Required Deliverables: 1)Complete 3D CAD Assembly files (SolidWorks or STEP format) of the internal juicing mechanism (cutting blade and roller/compression gears). 2)Outer sheet-metal enclosure design optimized for low-cost laser cutting and bending in India. 3)Production-ready 2D engineering drawings with clear tolerances for manufacturing handoff.

... Reference Brand : We love the clean design, layout structure, user experience, and overall professionalism. Important: We want a unique NOOK website that matches and exceeds the quality, user journey, and functionality of Pure Homes. Website Objectives The website must: -Inspire Visitors -Premium modern aesthetic -Beautiful homepage experience -Strong brand storytelling -Mobile-first design -Fast loading -Elegant animations -Generate Leads -Download plans -Request pricing -Book consultations -Download brochures -Capture enquiry details -Showcase Designs -13 home designs initially -Easily expandable -Custom design pages -Easy navigation between homes -High conversion journey -Build Trust -Customer testimonials -Build process

...residential builders. The finished site must be fully responsive on mobile and desktop, keep wording similar to what is there now, and use a restrained palette of white, black, grey and blue so nothing feels busy. Core structure • Pages: Home, About Us, Contact, Services, Projects and Blog. • Projects section: an easy-to-use photo gallery plus a simple news / updates feed so we can keep adding new housing projects ourselves after hand-over. What I expect • Custom or lightly-modified premium theme that loads FAST and meets current SEO best practices. • Visual consistency across browsers and devices. • Handover of all logins, theme files and clear instructions so our team can update text, photos and posts without developer help. • Project com...

...the cabinet space, hook it up, and confirm that everything runs perfectly. The old unit has already been removed, so there’s no disposal work—just a straightforward installation. Both the dedicated 120 V electrical circuit and the existing hot-water supply/drain lines are already in place and up to code. What I need is an experienced installer to: • Level and secure the dishwasher within the enclosure • Connect water, drain, and power, respecting manufacturer clearances and anti-flood requirements • Run a full test cycle to check for leaks, proper drainage, and correct electrical operation • Provide a brief hand-over on any adjustments or settings I should know Please bring any specialty tools (hose clamps, torque screwdriver, leak-testing...

...Fusion could do that.” ⸻ Prefer Practical, 3D-Printable Models Whenever possible, I would strongly prefer these tutorials to use practical models or actual useful objects, rather than completely random demonstration geometry. For example, if the tutorial is teaching a modelling technique, use that technique to create something such as: * A bracket * Phone stand * Clip * Hinge * Holder * Enclosure * Mount * Mechanical part * Storage accessory * Desk accessory * Tool * Snap-fit part * Functional 3D-printable object The exact object can vary significantly. The important thing is that the CAD tutorial should ideally result in something real and useful that can actually be 3D printed. This gives us another opportunity at the end of the video. After showing the faster Fu...

I'm seeking a skilled 3D artist to create high-quality CGIs for a modern single-family home. The renderings should be realistic and visually appealing, showcasing the architectural design and landscaping. Key Requirements: - Modern architectural style - Detailed landscaping integration - High-resolution, realistic renderings Ideal Skills and Experience: - Proficiency in 3D rendering software (e.g., SketchUp, V-Ray, Lumion) - Strong portfolio in modern housing CGIs - Experience in landscape design visualization - Attention to detail and creativity Please include samples of previous work in your bids.