Wireless sensors jobs
...current enclosure of my wrist-worn smart device exists as a Fusion 360 assembly, but it still takes too many steps to put together on the bench. Your task is to refine that design so the next revision is straightforward to assemble and friendly to large-scale CNC machining. You will start by reviewing my existing Fusion 360 file, tightening the external form, re-laying internal PCBs, battery and sensors, and adding all mounting, snap-fit or screw bosses needed for a clean mechanical stack-up. My top priority is making the enclosure easier to assemble and manufacture, so every decision—from wall thickness and draft angles to fastener choice—should reflect Design for Manufacturing principles. Once the architecture is locked, I need fully detailed, tolerance-controlled...
...specify manufacturer MPNs, datasheets, sourcing links, and mating pre-crimped JST harnesses for: (1) 2x IP65/IP67 enclosed cavity speakers (8Ω 2W) (2) 2x IP67 waterproof analog ECM mic capsules (silicone boots + hydrophobic membrane) (3) 1x IP65/IP67 illuminated metal momentary/latching pushbutton (O-ring sealed) (4) 4x IP67 waterproof door reed switches (5) 2x outdoor weather-sealed active motion sensors (PIR / 24GHz mmWave radar 0-1m). - **Hardware Design Constraints:** - Polarized/keyed connectors (JST-XH 2.54mm or JST-PH 2.0mm) with clear Pin 1 silk screen. - TVS diodes placed immediately adjacent to connector pins ahead of MCU tracks. - **Power Architecture & Sequencing:** - 12V, 5V, and 3.3V rails must fully stabilize before ESP32 EN/Reset is pulled high (brownout...
...operation on our harvester including GPS capture/data output/diagnostic logging/existing machine functions. The program must work on our machine to be considered complete. The hardware configuration includes: - NI cDAQ-9184 chassis - Two NI 9215 modules/one NI 9435/one NI 9472 - Emlid Reach RS3/RS4 GPS units Longer term we would also like a calibration tab for load cells/proximity sensors/potentiometers/similar sensors (outside immediate scope but updated program should accommodate). Proposed timeline: Complete development work excluding lab/field testing within six weeks of start date pending availability (please confirm feasibility). The University requires a consulting agreement to be approved before starting work; Mizzou will own all developed code. If this fits y...
Description: We have a complete, existing EasyEDA Pro project (schematic + fully routed PCB) for a compact wearable device. A design review found a short list of connection errors that must be fixed before fabrication. This is a revision job, not a new design. Board details Nordic nRF54LM20B (CSP61 / WLCSP package) with chip antenna (BLE) MAX77654 PMIC (charger + regulators), I2C sensors, QSPI flash 4-layer, 0.8 mm, 28 × 18 mm, blind vias, about 70 components Tool: EasyEDA Pro (project file provided) Scope of work Apply a provided list of schematic corrections (about 10 items: connecting several unconnected power and ground pins, re-wiring one inductor per Nordic’s reference design, one part-number change, minor net and value changes). A marked-up reference image an...
Add a new "Main water line" device to the Tuya Local Control Homey app that tells whether the main water line has water, based on the Main tank and Tank 2 level sensors and the main tank fill valve. 100% local, no cloud. - Water / No water tile plus a status line (water flowing, no water, valve closed, tanks full). - Valve open and level rising = water present. Valve open and no rise for a set time = no water. When the valve is closed or the tanks are full, it keeps the last known state (no false alarms). - All values set by the client in the device settings: rise amount, check time, no-water time, full level. - Flow cards: "Water arrived in the main line", "Water stopped in the main line", and the condition "Main line has / has no water", fo...
...temperature 2. Relative humidity 3. Atmospheric (barometric) pressure 4. Wind speed 5. Wind direction 6. GPS-based location, altitude and time Our approach is to source suitable sensing elements that are already commercially available and integrate them into our own instrument. The development would primarily involve designing the electronics and PCB, developing the embedded firmware, integrating the sensors, and designing a suitable outdoor enclosure. I would like to understand whether you have relevant experience in developing environmental monitoring instruments, sensor-based systems or similar products. Key Requirements: - Design a new circuit and PCB - Functionality to measure environmental parameters - Accuracy and reliability in readings Ideal Skills and Experience: -...
...matching owned manufacturing files. This is original development from written functional requirements; no existing schematic, PCB or firmware. External nominal 12 V supply. Two electrode pairs operate simultaneously in shared water, with current/voltage limits, controlled polarity reversal, retained polarity state, manual timed dosing, simple buttons/selector and actual-current indication. No wireless, app, display or production batch. Engineer must procure and receive the prototype, program and debug it at their own or managed facility, obtain an agreed representative electrode test fixture, perform documented shared-water and enclosed thermal validation, correct agreed-scope design errors including necessary hardware/re-spins/retesting, and ship a verified complete controller w...
...Role We are looking for a hands-on ESP32 & Electronics IoT Developer to join our distributed engineering team. You will be responsible for writing clean, reliable firmware, interfacing sensors and actuators, and building connected hardware prototypes from the ground up. Key Responsibilities * Firmware Development: Write, test, and debug efficient embedded code for ESP32 microcontrollers using ESP-IDF, Arduino framework, or MicroPython. * Hardware & Sensor Integration: Interface digital/analog sensors, relays, displays, and power modules over standard communication protocols (UART, SPI, I2C, ADC/DMA). * Wireless Connectivity: Implement reliable Wi-Fi, BLE, MQTT, HTTP/REST, or UDP data streaming between edge devices and local/cloud servers. * Prototyping &a...
...current enclosure of my wrist-worn smart device exists as a Fusion 360 assembly, but it still takes too many steps to put together on the bench. Your task is to refine that design so the next revision is straightforward to assemble and friendly to large-scale CNC machining. You will start by reviewing my existing Fusion 360 file, tightening the external form, re-laying internal PCBs, battery and sensors, and adding all mounting, snap-fit or screw bosses needed for a clean mechanical stack-up. My top priority is making the enclosure easier to assemble and manufacture, so every decision—from wall thickness and draft angles to fastener choice—should reflect Design for Manufacturing principles. Once the architecture is locked, I need fully detailed, tolerance-controlled...
...latency while keeping expansion options open. Once the network is set, PLC logic and microcontroller firmware must be written, fully tested, and commented. Typical tasks include managing pump speed, regulating flow rate, synchronising nozzle actuation with robot motion, and reading safety-critical sensors (pressure, temperature, level). Closed-loop PID control for flow consistency is essential. Hardware support is also required. I need a bill of materials covering drives, I/O modules, valves, sensors, and any gateway hardware, followed by purchase specifications and datasheets. If cost-effective off-the-shelf boards are preferable to custom PCBs, outline that path; otherwise provide basic schematics for a custom design. Deliverables • System architecture diagram ...
I need a manufacturer-independent, single-unit Data Diode that guarantees one-way traffic from my operational equipment into the corporate IT network. On the OT side I have industrial controllers and sensors communicating over Modbus TCP; once the data reaches IT it must be forwarded seamlessly into an MQTT/MQTTS broker so other applications can subscribe. Key expectations • Hardware or virtual appliance that physically enforces unidirectional flow (OT âž” IT) with no return channel. • Native parsing of Modbus TCP on the inbound side and automatic repackaging or bridging to MQTT/MQTTS on the outbound side. TLS support is required for secure MQTT connections. • Configuration interface that lets me map Modbus registers to MQTT topics without vendor lock-in. &bull...
I need my wired GameSir Tegenaria Lite opened, fitted with a Raspberry Pi Pico and two MPU-6050 gyro sensors exactly as shown in the alpakka-lite guide (), then closed up so the pad still looks stock. The one visible change I do want is a pair of small capacitive-touch patches on the top edge—one beside each shoulder button. Each patch is simply a 3 mm hole with a wire looped through and secured under conductive tape, the free end going to an unused Pico GPIO, identical to the touch point in the original wiring diagram. I will hand you: • the controller • the Pico (pre-headers) • two gyro boards • conductive copper tape • resistors, screws, tape, hot-glue sticks and solder Please bring only the thin, flexible stranded wire needed
...to modify a wired game controller (GameSir Tegenaria Lite) by fitting a Raspberry Pi Pico and 2 gyro sensors inside it, based on this open source project with full instructions and wiring diagram: I'd also like one extra thing included that is not in the official guide: 2 small touch patches on the top edge of the controller, as in this PHOTO: Each patch is a small hole in the shell with a wire passed through and held under conductive tape, and the other end goes to a spare Pico pin. The wiring is the same as the touch point in the guide. I'll handle the firmware myself. I already have the controller and will supply the Pico, the 2 gyro sensors and the conductive tape. Would you already have the small items, such as 100k resistors, thin stranded
Logo Design Brief: SmartyMicro Smart Microwave I am seeking a creative graphic designer to develop a professional, modern and memorable logo for SmartyMicro, an innovative smart microwave concept. SmartyMicro uses three temperature sensors—positioned at the top, bottom and side—to help users heat food and drinks to their preferred temperature. The technology is designed to reduce overheating, spills and burning. Logo requirements: - Clearly connect the SmartyMicro name with the microwave concept. - Creatively combine the letters S and M with a microwave-inspired symbol or shape. - Convey smart technology, innovation, simplicity and reliability. - Use a clean, modern and professional style; avoid cartoonish or overly complex designs. - Be distinctive, recognisable and ...
...desired food or drink temperature, connect to the microwave, monitor the heating process, and receive notifications when the food reaches the selected temperature. The microwave uses sensors to detect temperature and help prevent overheating, spills, and burning. I want the app to have a simple, clear, modern, and user-friendly design. The app should work on both iPhone and Android devices. The app should connect to the microwave using Bluetooth when the user is nearby and Wi-Fi for remote monitoring and control, where supported by the appliance. Key Features: 1. Smart Sensors: SmartyMicro includes three sensors. Their main purpose is to collect information about the food during heating. 2. Control System: This allows users to choose their preferred temperature. ...
...in an indoor, well-controlled lab setting. Here is what I expect from you: • A brief but clear explanation of the flow calculations you use to size the pump, showing how the ball’s mass, tubing diameter, head losses and desired velocity translate into the chosen flow-rate/pressure specs. • Selection of off-the-shelf components: pump, reservoir or manifold, standard tubing material, and any sensors or valves you feel improve reliability. • Fully modelled custom fittings and junctions designed specifically for 3-D printing (FDM or SLA), supplied as STEP or STL files ready for print without supports in hard-to-remove places. • A concise bill of materials that ties everything together, including print material recommendations (e.g., PETG, ABS, resin)...
...sheets stop inside the machine, right around the toner / fuser section, so I suspect the feed path or fuser rollers need attention—possibly a pickup clutch, worn rollers, or a sensor giving false feedback. I need a technician who knows this model inside out to inspect, diagnose, and eliminate the jam source, then test the machine until it runs a full stack smoothly. Replacement parts (rollers, sensors, fuser parts) can be billed separately once we confirm what is required; I’m happy to approve them quickly so the fix isn’t delayed. Please outline how soon you can be onsite, your experience with Ricoh colour MFPs—especially the MP C6004 or similar—and what checks you’ll perform before and after the repair. A short post-service report confi...
Freelance hardware design engineer (wearable devices) Advance Info Tech is looking ...Define the hardware architecture and select components Design the power system, schematic and PCB layout Prepare the manufacturing files Bring up the first boards and hand over to our firmware team What we are looking for 3-7 years of hands-on experience designing wearable or other compact, low-power devices Experience with some of: cellular (LTE) modules, GNSS, Bluetooth LE, motion and optical sensors, battery charging and fuel gauges Strong PCB layout skills for small boards, including RF and antenna placement Proficiency in Altium or KiCad A portfolio of earlier boards that reached prototype or production Confirmation that you are free to take freelance work, with no conflict with your curren...
...design to have several options for section details, so it is important to provide transitions between materials and heights that incorporate lighting. Think about soffits, valances, backlighting, grazing, etc.) You need to provide the following on your RCP. • Luminaire layout • Switching & Switching loops • HVAC Supply and Return • Sprinkler locations • Emergency Lighting • Exit lights/signs • Sensors (daylight, occupancy) • Smoke/heat, AV alarm systems, CO2 monitors • Ceiling Heights • Ceiling materials (this is a commercial space, most of the ceiling should be some sort of acoustical ceiling product) Be sure to include soffits, coves, or interesting design features for your detail drawings. • Should include dimensioning...
We have a working 2-board wireless battery monitoring system and need an experienced hardware engineer to complete a design revision (rev-B) and production files. EXISTING SYSTEM (all files provided, KiCad + Arduino/ESP-IDF source): - Transmitter PCB: ESP32, 2x ADS1115 (16-bit ADC) reading 4S/5S/6S lithium cell voltages via divider network, 3 relay outputs, XL1509 buck + LM1117 3.3V LDO. Powered directly from the battery pack (max 16.8V). - Receiver PCB: ESP32 + 3.5" ILI9481/ILI9488 TFT, receives data via ESP-NOW. - Firmware for both boards is working (cell readings, two-point calibration, ESP-NOW, display UI). SCOPE OF WORK: 1. Review the existing KiCad project and firmware. 2. Transmitter rev-B design changes: - Add proper input protection: TVS, input fuse / overcurrent ...
Complete engineering and prototype development of a wireless sensor-triggered fluid dispenser system. Milestone 1 – Analysis & Assessment — AUD 50 Review requirements, assess technical feasibility, define system architecture, wireless approach, pump/sensor options, and key technical risks. Milestone 2 – Development & Engineering — AUD 1,450 Complete system engineering, wireless communication, firmware architecture, pump/trigger integration, and prototype development. Milestone 3 – PCB Design & Electronics — AUD 600 Complete schematic, PCB layout, power management, USB-C operation, component selection, and electronics documentation. Milestone 4 – Components & Prototype Fabrication — AUD 400 Procure comp...
I have a stubborn Wi-Fi / internet connection problem that I can’t pin down. As a recent Computer Network Technology graduate I’m comfortable with TCP/IP, routing, switching fundamentals and basic troubleshooting, b...netsh, etc.), and capture packets with Wireshark if needed. The network is small, so we should be able to iterate quickly. Deliverables (once we’re done) • A working, consistently stable Wi-Fi connection • A brief step-by-step summary of what we changed so I can document it for future reference • Any configuration files or screenshots that are critical to the fix If you specialise in wireless interference analysis, advanced router configuration, or have experience with consumer-grade hardware that drops connections unpredictab...
...vacuum head for small adhesive labels. - Vacuum pressure sensors to confirm successful pickup. - Automatic vacuum release. - Replaceable suction cups. - A suitable compliant application surface to prevent label wrinkles. - Modular tooling at the robot wrist. ## 4. Machine Vision The system must include cameras and vision software capable of: - Detecting the presence and position of parcels and envelopes. - Identifying dimensions and orientation. - Determining suitable label application positions. - Guiding the robotic arm. - Verifying successful label application. Possible technologies: Raspberry Pi, OpenCV or industrial machine vision systems. ## 5. Existing Rollo Wireless Printer – Must Be Preserved We already operate a Rollo Wireless thermal label pri...
...Proven experience designing AC/DC power supplies or motor control boards Hands-on experience designing products to UL standards and supporting UL certification Ability to produce clean, production-ready wiring diagrams and schematics US-based and available during Central Time business hours Willing to sign an NDA Preferred: Experience with electromechanical equipment (motors, blowers, solenoids, sensors) Experience with [your tools, e.g., Altium, KiCad, AutoCAD Electrical Solid works] To apply, please include: A short summary of historical experience for a power supply or motor control board you designed, including the UL standard involved Examples of wiring diagrams or schematics you’ve produced, with sensitive details removed Your hourly rate and your availability over ...
...the schematic and PCB for one irrigation controller. This is a hardware design job. Firmware is not included. The controller runs from 24 V DC. The MCU is fixed: Espressif ESP32-WROOM-32UE, external antenna, , at least 4 MB flash. Not a module with a PCB antenna, and not a development board. The board has wired 10/100 Ethernet and USB-C programming. Inputs: 3 float switches, 3 NPN level sensors, 2 pressure transducers, 1 pulse flow meter, and 1 two-wire leak probe. Outputs: 6 low-side MOSFET channels (2 solenoids, 1 irrigation pump, 1 mix pump, 2 low-current spares). A load may be 12 V, 24 V, or 48 V. Only the irrigation pump reaches 10 A. The load positive is terminated off the PCB. The board switches the return only, and the MOSFET must be rated for a 48 V inductive load. On...
...915 MHz, KiCad) DESCRIPTION: I'm developing a low-power LoRaWAN wearable device and I'm looking for an experienced electronics engineer to handle the complete hardware design. I handle firmware, backend and field testing myself. Scope: - Schematic and PCB layout in KiCad (likely 4 layers) - 915 MHz RF design around an STM32WL (integrated LoRa), with external antenna - GPS module and a few I2C sensors - Ultra-low-power design on a primary (non-rechargeable) cell, with switchable power domains - A high-voltage pulse output stage with a hardware-level fail-safe - Manufacturing-ready files for JLCPCB SMT assembly: Gerbers, BOM with LCSC part numbers, pick & place, assembly drawings - Short design rationale document explaining key decisions - Support during bring-up of...
I need a new Click PLC program developed from the ground up for a machine that used 10 sensors approximately and eight outputs. It uses click PLCs from automation direct. Must be willing to do a screen share, and a phone call or audio call
...manufacture and packaging, and overall look The next iteration needs a built-in digital display that: • Shows live workout duration, force produced and limb range of motion • Delivers real-time feedback while the exercise is in progress • Saves each session so users can review progress over time You would take the project from concept to proof-of-concept prototype. That means selecting the right sensors (load cells, IMUs or similar), integrating them cleanly into the frame, building or sourcing a compact screen, writing the embedded firmware to capture and display the metrics, and creating a simple data-logging workflow (on-device storage or Bluetooth companion app—whichever is fastest to implement). What I need at hand-off: 1. Updates drawings and d...
...terminology and questions. - Join client calls and help explain my engineering work and proposed solutions in clear English. - Turn my technical explanations into clear, natural English for clients while preserving their meaning. - Ask clarifying questions about requirements, constraints, priorities, and acceptance criteria. - Help communicate topics such as embedded firmware, microcontrollers, sensors, PCB design, connectivity, testing, and hardware/software integration. - Confirm technical answers with me when a question goes beyond the agreed briefing. - Prepare concise meeting summaries, action items, and follow-up messages for my review. - Keep client information confidential and follow agreed access and document-sharing arrangements. TECHNICAL RESPONSIBILITIES AND...
Senior Embedded Systems Engineer – Custom Wireless Soil Sensor Development Project: SoilVision 2.0 Location: Remote – International applicants welcome (Indian engineers particularly encouraged) Engagement: Freelance / Fixed-price project Initial Budget: Not yet confirmed 1. About the Project We are a student-led agricultural technology team based in Zimbabwe, developing a project called SoilVision. Our original project, presented at the Zimbabwe Science Fair, combined a commercially available soil sensor with our own offline web application, developed using React and JavaScript. We are now developing SoilVision 2.0, with the ambition of designing and building our own proprietary wireless soil-analysis device. We are seeking an experienced Embedded Systems En...
...solution that tracks teeth-grinding and jaw-clenching events while I sleep. Detection will rely on a night mouthguard fitted with pressure and motion sensors, complemented by a lightweight wrist bracelet that streams additional data to an AI-driven mobile app. During every sleep session the mouthguard must capture, timestamp, and store both the number and the length of each grinding or clenching event. The companion app will process these readings in real time, present an easy-to-read nightly report, and archive historical trends so a dentist can review progress. Deliverables expected • Functional mouthguard prototype with embedded sensors and low-power Bluetooth firmware • Simple wrist bracelet prototype that pairs seamlessly with the guard and app &bu...
...Orientation: shoot horizontal, framed so it can be cropped to vertical 9:16. Keep the subject centered with room around them and nothing important at the edges. Shoot a handful of the best detail shots vertically as well. - Audio: wireless lavalier mics on the homeowner and the interviewer, recorded as separate WAV files (48 kHz, 24-bit), plus camera audio as backup. Clap or slate at the start of each take, and record 30 seconds of room tone. Audio is critical. - Picture settings: natural or slightly flat look. No filters or baked-in color. - Gear: 4K camera, wireless lavaliers and a separate audio recorder, gimbal or stabilizer DELIVERABLES: original, uncompressed files straight off the camera and recorder, uploaded to a shared Google Drive folder within 2 business days,...
...capture high-quality footage and stills, manage the shoot efficiently, and deliver polished final content. Please include your availability, relevant experience, and examples of similar work. We need an assistant from your end to manage sound part as well Event Details: * 70–90 guests at a bar venue * 20-minute live podcast recording with up to 6 speakers * 2-camera setup (wide + close-up) * 6 wireless microphones with separate audio tracks, plus ambient recording * Audio setup with venue PA * Portable lighting suitable for a dark bar * Event photography and vertical B-roll footage * Raw video, audio and photos delivered in 6 to 8 hours No editing needed only raw footage...
...gravel and mildly rough terrain. The project should focus on mechanical stability, reliable wireless control, mobility, basic camera integration and modular design. 2. Key Technical Requirements A. Mechanical Design * Compact tank-style tracked chassis. * Two independent DC geared motors with differential steering. * Durable tracks suitable for sand and uneven gravel. * Stable chassis with adequate ground clearance. * Provision for mounting a lightweight camera and electronic components. B. Electronics and Control * Arduino-based control architecture (Arduino Uno, Mega or ESP32, as appropriate). * Motor driver and suitable power management system. * Rechargeable battery-operated system. * Wireless remote-control capability. * Emergency power cut-off and fail-safe beh...
...the nanotech-level programming that lets my patented control software speak to the screen and, in turn, trigger the external device through Bluetooth or Wi-Fi. Here is the flow I’m aiming for: a user issues one of the three predefined gestures or touches, the screen’s embedded code recognises it immediately, and a secure wireless packet is sent to the paired device, which then carries out the linked action. All logic that interprets the gestures and handles the wireless handshake should reside on the screen’s own microcontroller so the external device remains lightweight. You will work directly with my proprietary API (documentation supplied after NDA) and deliver firmware that: • Maps the three commands to my exact protocol • Handles relia...
...a clean, responsive website that immediately tells visitors who we are and what we do in ELV turnkey projects, surveillance & home automation, and networking, structured cabling & wireless solutions. The site’s core purpose is to showcase these three service streams in depth and highlight the quality of work we have already delivered. Structure I have in mind • Home page with a concise value proposition, striking imagery and quick links to each service area. • Three dedicated service pages—one for ELV turnkey projects, one for surveillance & home automation, and one for networking / structured cabling / wireless—each with space for diagrams, photos, feature lists and a clear call-to-action. • Project gallery that can be fil...
I need a talented graphic designer who can jump in right away and craft a single, large “eye” motif—rich with sparkling, galaxy-style color—perfectly centered on a round wireless charger surface. Think deep cosmic hues, star-like specks, and subtle gradients that feel premium rather than busy; the final result must be striking from a distance yet polished up close. My printer requires a print-ready file with bleed and safe zones marked, 300 DPI (or vector), in either Adobe Illustrator or Photoshop format. Please keep layers intact so minor tweaks to colors or placement remain possible on my side. Deliverables • High-resolution, press-ready artwork sized to the charger template • Editable source file (AI or layered PSD) • A flattened previ...
We are looking for an experienced Industrial IoT / Hardware Developer to design and install a machine monitoring system for our manufacturing plant. Requirements: Install current sensors (CT sensors) on 9 industrial machines to detect ON/OFF status based on electrical current. Automatically record every ON/OFF event with date and timestamp. Calculate daily machine running hours. Display real-time ON/OFF status of all machines. Send machine data to our cloud-hosted database. Provide API integration support for our existing mobile and web applications. Scope of Work: Hardware selection and procurement. Complete hardware installation and configuration. IoT controller and firmware development. Cloud connectivity and API integration. Testing, calibration and commissio...
...electronics packaging in CAD: mounting for the display, camera, sensors, LEDs, controller and wiring; protect electronics from stepping loads; keep it serviceable; prepare parts for 3D printing or CNC Build a simple mobile-friendly web control interface that communicates with the controller (REST / WebSocket / MQTT / BLE) Prepare the BOM, wiring diagrams and step-by-step assembly instructions for our technician in California Lead remote troubleshooting, integration testing and the final functional demonstration by video call Deliver all firmware/source code, CAD files, drawings and configuration files Requirements Hands-on experience with real physical hardware, not software-only projects ESP32 or similar MCU; Embedded C/C++; sensors; RGB/RGBW LEDs; displays; Wi-Fi/BLE C...
Title: Embedded + mechanical engineer: wireless sensor-triggered fluid dispenser prototype Project Build a proof-of-concept of two paired units: a remote trigger and a dispenser. The trigger is either a motion sensor or a weight-threshold pad (wired to the trigger unit). The units link wirelessly so the trigger can be mounted remotely. One trigger pairs to one dispenser. Indoor use. Water-based fluid. Full application details shared under NDA after shortlisting. Requirements User-adjustable on the dispenser: spray duration, activation delay, force, and pattern (fine mist or direct stream) Weight trigger works as a simple threshold trip, same behaviour as motion Both units: rechargeable battery, USB-C charging, and direct USB-C operation that bypasses the battery Enclosure: 3D-pri...
...Engineer Needed – Confidential Hardware Startup Project I am a UK-based entrepreneur developing a new technology product and looking for an experienced electronics engineer to help me build an initial prototype. The project involves developing a compact, battery-powered smart electronic device with wireless connectivity and a companion mobile application. I am looking for someone with experience in: - Electronics and circuit board design (PCB) - Embedded systems and firmware - GPS and wireless connectivity - Battery-powered devices - IoT (Internet of Things) - Product prototyping and testing - Preparing products for manufacturing Initial requirements: 1. Review the technical requirements. 2. Recommend suitable electronic components. 3. Explain how a working prototy...
...RTD temperature input module. HMI Hardware: Flexem 7000 Series HMI (FE7000 / FE7300) communicating via RS-485 Modbus RTU (COM1 port, 9600 baud, 7 data bits, Even parity, 1 stop bit). 2. Scope of PLC Programming (WPLSoft) Analog Data Acquisition: Configure FROM/TO instructions to read PT100 Class A temperature sensors (Chamber live temperature D100, specimen safety temperature D102, and refrigeration coil temperature D104) along with analog pressure transmitters and humidity sensors (D110 to D115). Compressor Cascade Sequencing & Interlocks: Implement master safety interlocks (M0 derived from emergency stops, door switches X2, and water/airflow flow switches X3). Program a 2-minute equalization timer (T0) and strict sequence interlocks ensuring the Higher Side comp...
I run a Wialon Hosting account that tracks Suntech and Cellocator devices and need every location update forwarded, in real time, to Overhaul’s HTTPS REST endpoint. Overhaul expects JSON messages that contain all data the device produces—position, timestamp, speed, heading, sensors, alerts—and they want each message tagged with the exact unit name or code we use in Wialon. You may solve this by fine-tuning Wialon Retranslator, wiring a webhook, or building a light middleware that reshapes the raw feed into the required JSON schema. Whichever route you take, the flow must be reliable, low-latency, and easy to expand when new units come online. Key objectives • Continuous push of Suntech and Cellocator data from Wialon to the Overhaul REST API. • Strict...
...environment (a room under construction with sheetrock panels, as in the image). 3. Simulate the robot doing its work in sequence: driving into position, installing a sheetrock panel on a wall, applying joint compound to the joints, sanding the joints smooth, and painting the wall — including the mast extending, the torso rotating, and the arms using the automatic tool changer for each task. 4. Add basic sensors (a camera at minimum) and show the robot perceiving its environment. 5. Deliverables: the complete Isaac Sim project files, a short written summary of how the model is set up and how to run it, and a screen-recorded video of the simulation running. Budget: $250–750 USD for this simulation project. Please bid with examples of your NVIDIA Isaac Sim, Omniverse, o...
...specify manufacturer MPNs, datasheets, sourcing links, and mating pre-crimped JST harnesses for: (1) 2x IP65/IP67 enclosed cavity speakers (8Ω 2W) (2) 2x IP67 waterproof analog ECM mic capsules (silicone boots + hydrophobic membrane) (3) 1x IP65/IP67 illuminated metal momentary/latching pushbutton (O-ring sealed) (4) 4x IP67 waterproof door reed switches (5) 2x outdoor weather-sealed active motion sensors (PIR / 24GHz mmWave radar 0-1m). - **Hardware Design Constraints:** - Polarized/keyed connectors (JST-XH 2.54mm or JST-PH 2.0mm) with clear Pin 1 silk screen. - TVS diodes placed immediately adjacent to connector pins ahead of MCU tracks. - **Power Architecture & Sequencing:** - 12V, 5V, and 3.3V rails must fully stabilize before ESP32 EN/Reset is pulled high (brownout...
Phase 2 of the boat lift monitor, per our chat of Nov 2-3. 4 milestones at $250, each funded one at a time and released after testing on my hardware: M1 fixes + SMS opt-in (Nov 7); M2 carrier board design, reviewed before ordering (Nov 14); M3 firmware/dashboard for 4 clamps + 4 sensors (after boards arrive); M4 first board built and tested. I order fab/parts. Deliverables: KiCad source, Gerbers, code in our GitHub. All designs and code belong to Ascend Boat Lifts, LLC.
...any laptop or phone browser on the same network. Location: Bangalore, India (preferred to work from office where the Hardware is located) Current hardware already on board • Raspberry Pi running ROS 2 Humble (we have purchased a new module, as existing RPi seems to have issues, troubleshooting would be required) • Luxonis OAK-D Lite on a small pan-tilt head • LD19 360° LiDAR No other sensors, lights or emitters may be added; the solution must rely entirely on those three devices.(we already have lights in the bot) I have some ROS 2 nodes running, but depth frames from the OAK-D Lite no longer publish correctly and the LiDAR scan topic is intermittent. Step one is to restore clean, time-synced data streams. Real-time boundary detection requirement...
...sleeve—think of a cigar-style wrap more than the typical small sealed bag. Scope of work • Model every mechanism required to singulate wafers, build the stack, feed and cut the paper, roll it tightly around the stack, seal the edge, and discharge the finished pack. • Keep the wrap diameter consistent and allow quick change-over for different wafer lengths. • Use readily available motors, sensors, bearings, and fasteners wherever possible; show them inside the assembly with correct part numbers. • Include motion studies so I can visualise the stacking and wrapping sequence and verify that the wafers stay aligned. • Provide fully editable SolidWorks (2021 or later) files plus PDFs of assembly drawings, exploded views, and a basic bill of ma...
I need an embedded-system expert who can take my rough concept and turn it into a working hand-held device that reliably tells the user whenever a camera—hidden or otherwise—is nearby. The unit must combine two techniques: an RF scan to pick up wireless video signals and an optical sensor that pings for lens reflections, so an attacker cannot defeat the device by switching transmission modes. The job covers the entire design cycle: selecting the MCU or SoC, drawing the schematics, laying out the PCB, writing the firmware that fuses data from both detection methods, and proving everything works on a breadboard or quick-turn prototype. Low power consumption and a straightforward LED or buzzer alert are fine for the first iteration; once that is stable we can talk refineme...