Firmware Development Jobs

I have a custom board built around the STM32G031 and I want a clean, production-ready firmware project created in C with STM32CubeIDE. Your first task is to bring the microcontroller to life: set up the system clock, configure the required GPIO pins, verify the build, and program the device. Here is the scope I need covered: • Create a CubeIDE project that targets STM32G031, using either HAL or direct LL drivers where it makes sense. • Configure clock tree (HSE, HSI or internal PLL as required) so the MCU runs at the specified operating frequency. • Initialise all GPIOs I mark on the schematic; direction, speed and pull settings must match the hardware design. • Build, generate the .hex/.bin files and flash them onto the board through ST-Link over SWD. • ...

Descripción del Proyecto: Busco un ingeniero electrónico para diseñar el esquemático y la placa (PCB) de un dispositivo IoT educativo llamado FAZI. Es un presentador, Air Mouse y teclado inalámbrico para docentes. OJO: Yo me encargaré del 100% de la programación (Firmware) y de la integración vía Wi-Fi con mi servidor. El trabajo que requiero de ti es únicamente el diseño electrónico y ruteo en KiCad para mandar a ensamblar. Requisitos de Diseño Físico y Arquitectura: Forma de la placa (Crucial): La PCB debe tener un formato alargado y estrecho, imitando un lápiz, puntero o varita mágica (dimensiones sugeridas: 20-22 mm de ancho por 100-120 mm de largo). Integración a ...

I need an embedded-software specialist who can take my collection of Wi-Fi and LoRaWAN gateways and assorted sensors and knit them into a single, production-ready IoT platform. The job covers the full stack from firmware that runs on the edge devices through to the application layer that users will see. Core capabilities the platform must deliver: • Data collection from every gateway and sensor • Robust device management (on-boarding, remote configuration, OTA updates) • Built-in analytics so I can visualise trends and run simple rules without exporting data elsewhere You’ll be free to recommend languages, embedded RTOS options, and cloud back-ends, provided they reliably handle both Wi-Fi and LoRaWAN traffic and scale cleanly as more hardware is added. Deliverables...

我手中有一块已从设备上拆下、保持完好的 7037IC 芯片，现需安全、无损地读取其中的手机操作系统固件。请基于下列要点完成一次性交付： 1. 精准读取 • 目标仅限操作系统固件；若过程中顺带获取基带或引导固件，可在说明中备注，但不必交付。 • 可接受以下接口： - ISP - JTAG - NAND Flash 编程器 2. 完整性校验 • 交付时请同时提供 SHA-256 等哈希或同等级别的校验值，证明数据未缺失、未被篡改。 3. 交付格式 • BIN 或 HEX 文件（二选一即可） • 简要读取日志或说明文件，便于日后分析与重复验证。 补充资料与配合 • • 期待流程对芯片零损伤。 • 项目需由在美国本地运营的公司完成，以便后续沟通及物流。 申请须知 • 请说明你在 ISP、JTAG、NAND Flash 读取方面的实际经验与成功案例。 • 简要描述你的设备、软件工具链和防范静电／过压等保护措施。 达到上述要求并一次性交付完整映像与校验文件，即视为项目完成。

Hello Yernaidu, Thank you for your proposal. I'm interested in working with you on my Big Hero 6-inspired modular micro-robot project. I would like to clarify exactly what is included in your **$30 quotation**. Does this price cover the complete engineering design package, including: 1. Complete mechanical CAD and 3D modeling (editable source files, STEP, STL, and manufacturing drawings). 2. PCB schematic and layout design, including Gerber files and BOM. 3. Two independently controlled robotic arms with adjustable angles and a target of 360° rotation. 4. Forward and backward movement mechanism. 5. Robot-to-robot docking and separation mechanisms. 6. Relative position detection between robots. 7. Bluetooth communication and microcontroller firmware. 8. Python-based PC software...

1. Project Overview & Architecture The goal of this project is to design a set of modular, decentralized expansion PCB boards for grow tent automation. Instead of a rigid central mainboard, each expansion board functions as an independent node powered by a localized ESP32-C3 Supermini module, communicating via Wi-Fi/MQTT through ESPHome into Home Assistant. To reduce clutter and eliminate the need for multiple external power supplies, all boards will share a common power distribution concept: 12V DC Input (via standard 5.5x2.5mm barrel jacks or terminal blocks) with onboard step-down regulation (e.g., Buck converters) to supply 5V and 3.3V where needed, allowing a single 12V barrel power supply to be daisy-chained across boards. 2. General Requirements for All Boards Microcontroller: ...

I am looking for an experienced power electronics engineer or engineering team to design a residential-scale hybrid solar inverter for commercial production. The project involves developing a single-phase, 230 V AC, 50 Hz pure sine-wave hybrid inverter that integrates rooftop solar panels, a lithium battery bank and the utility grid. The design should prioritise high efficiency, reliability, safety and ease of manufacturing. I prefer an engineer with previous experience designing working solar inverters, grid-connected converters, MPPT controllers and bidirectional battery systems. An existing, validated reference design that can be licensed or transferred is preferred. 1. Target Specifications Rated power: 1–5 kW continuous AC output: 230 V RMS, single phase, 50 Hz Output wave...

I’m looking for a freelancer who can help me perform SW updates to the Automotive Audio Amplifier. The parts are not in the vehicle and are located in El Paso. Here’s what I need from you: • Identify the correct update package for the hardware revision and regional SKU. • Prepare the setup for flashing using the directions from the Supervisor. • Execute the update, capturing logs so we can verify a complete, error-free install. • Follow required protocol to ensure traceability and ensure things are working properly. If you’ve worked with OEM infotainment systems, custom ROMs, or related tools such as ADB, QFIL, or OEM flashing utilities, that’s a plus. Required short term contract of 2-3 weeks (potentially future contracts depending on p...

I need a skilled PCB designer to convert my existing through-hole PCB, designed in Fritzing, into an SMD PCB for production using KiCad. The design works great, but I need it to be SMD. Requirements: - Convert the following components from through-hole to SMD: - ICs (including ESP32, A7670G modules, and charge controller) - Use of standard footprints for all SMD components. Ideal Skills and Experience: - Proficiency in KiCad - Experience with SMD PCB design and layout - Familiarity with the specified components (ESP32, A7670G, charge controllers) - Attention to detail and accuracy in design Please provide samples of previous SMD PCB designs.

My BMZ Power2Go Work portable power station—just 14 months in service—shut down abruptly while delivering a steady 1 600 W load (it is rated for 2 500 W continuous, 3 600 W peak). Since that moment it refuses to charge or power on; every status LED remains dark. I need a battery technician who can carry out a full diagnostic and bring the unit back to life. That means opening the enclosure, verifying cell health, checking the BMS, charger circuitry, DC-AC inverter stage, and any internal fuses or relays. Once the fault is identified I want the defective components replaced or rebuilt so the pack can once again charge fully and supply its original output ratings without thermal or voltage irregularities. Deliverables: • Detailed test report outlining root cause, measureme...

iPhone Battery Management System inside-out and can work across software, hardware, and firmware layers to alter the way battery health data is reported. The goal is to change the internal metrics that feed the Health section in iOS so the device shows revised capacity, cycle count, and related statistics without triggering errors or safety lockouts. Can you make a Custom device that can be use on a factory level,hat helpful to change battery health and cycle by just connecting the battery BMS only. Scope • Reverse-engineer or otherwise access the BMS firmware and its data pathways. • Modify the algorithms or calibration tables that calculate battery health. • Validate the change on real hardware so the phone operates normally under charge, discharge, and idle state...

Hello PCBWay, I need you to design and supply a fully assembled, programmable PCB for a battery-powered motion recorder. I do not have a schematic and cannot solder components myself. Please check whether an existing design could be adapted to reduce the cost. **Shape and size** - Rectangular PCB with rounded corners. - Standard credit-card dimensions: 85.60 × 53.98 mm. - Keep the PCB and components as thin as practical. - A separate flat LiPo battery will sit behind the PCB. Please keep the battery area clear of tall components. **Hardware** - A low-cost, low-power microcontroller that I can program myself. - An onboard 3-axis accelerometer and 3-axis gyroscope. - Two assembled push buttons: 1. Power on/off. 2. Start recording; press the same button again to stop and save. - One pro...

I need a production-ready PCB for an industrial ranging device that will be integrated into larger automation machinery on our factory floor. The board has to combine three core capabilities: robust signal processing of the sensor data, reliable high-power outputs to drive downstream actuators, and on-board wireless communication for status reporting and firmware updates. The footprint must stay within 80 mm × 60 mm, operate from a 24 V DC rail, and meet industrial EMC/EMI standards (EN 61000 family). A multilayer stack-up with controlled impedance traces for the RF section is expected, along with generous creepage/clearance on all high-current paths. Deliverables • Schematic (Altium or KiCad) • Fully routed Gerber/ODB++ files ready for fabrication • Annotated ...

I need a complete electrical design for a true-online 600 W UPS that will operate in a home environment. The scope covers everything from the high-level architecture down to production-ready documentation, so that I can have the unit prototyped and assembled without further engineering work. What I expect you to produce includes: • Full schematic with clearly annotated component values • Bill of materials using readily available parts • PCB layout files (Gerber or equivalent) and 3-D board view • Control logic or firmware source (if a microcontroller or DSP is used) • Mechanical outline showing heat-sink placement, transformer or inductor dimensions, and suggested enclosure size • Brief test plan describing how to verify continuous 600 W output, transfer time...

Embedded Systems / Firmware Engineer Project Description HappyMat(TM) is seeking an experienced Embedded Systems / Firmware Engineer for HappyMat Prototype #1. You will be responsible for the prototype's embedded controller, firmware, sensor integration, LED control, digital display, wireless communications, and associated hardware/firmware integration. Primary Responsibilities • Develop and configure the embedded controller and firmware. • Integrate pressure/presence sensing. • Integrate addressable LED lighting. • Integrate the digital display. • Implement Wi-Fi connectivity. • Implement Bluetooth/BLE connectivity. • Support camera, speaker, and microphone integration. • Coordinate with the IoT/interface engineer where applicable. • Tr...

Busco un ingeniero de sistemas embebidos para el desarrollo del firmware base de un MVP en fase pre-semilla. El proyecto consiste en la integración en laboratorio de un microcontrolador ESP32 WROOM programado en C++ (FreeRTOS / Arduino IDE) que coordine la lectura de sensores y la activación autónoma de actuadores de seguridad urbana. Requisitos técnicos del sistema: • Gestión de Energía: Modos de bajo consumo (Deep Sleep) y activación por interrupciones físicas GPIO externas. • Integración de Sensores: Matriz térmica I2C (AMG8833), micrófono digital I2S, sensor ultrasónico de distancia, termistor digital DS18B20 y sensor digital de conductividad/presencia de agua (detección de desbordamien...