Microcontroller Jobs

I'm looking for an Arduino code that will trigger RGB LEDs to change color based on a pulse rotary dial input. Requirements: - Use of a pulse rotary dial - RGB LEDs whose colors will be controlled by the rotary dial input Ideal Skills and Experience: - Proficient in Arduino programming - Experience with rotary dials and RGB LED control - Familiarity with electronics and circuit design

Hello , I have a cabled weather station ready to go, but I need an experienced hand with the physical installation side only. The job covers everything from mounting the sensors and console, running and securing the cable, to making sure connections are weather-proofed, grounded, and reading correctly once powered up. Brand is flexible—I simply need someone familiar with the usual hardware found in systems such as Davis Instruments, AcuRite, La Crosse, or similar. Only serious freelancer Auto bids not good Thank you

I have a cabled weather station ready to go, but I need an experienced hand with the physical installation side only. The job covers everything from mounting the sensors and console, running and securing the cable, to making sure connections are weather-proofed, grounded, and reading correctly once powered up. Brand is flexible—I simply need someone familiar with the usual hardware found in systems such as Davis Instruments, AcuRite, La Crosse, or similar. Key Deliverables • Sensors, mast, and console solidly mounted in their designated locations • All cables routed neatly, protected from the elements, and correctly terminated • Grounding and surge protection in place where required • Final power-up and verification that the station is delivering clean, sta...

I’m putting together a compact two–tier electronic enclosure and I need the complete assembly modelled in Shapr3D so I can open, review, and tweak the layout myself. Here’s the flow of work: • You’ll source accurate 3 D models for several off-the-shelf parts plus one OEM component. I already have its detailed specs in PDF, which I’ll forward immediately. • Once the parts are ready, you’ll position them inside a base housing roughly 10 in × 9 in × 2.5 in, then add a second enclosure that stacks neatly on top. • Please illustrate the electrical and fluid links: a triple-lumen 1⁄16″ ID umbilical running between the tiers, and wiring that ties a water-level sensor, a peristaltic pump, and an Arduino-class controlle...

I’m developing a compact medical-grade board that will sit at the heart of a new vital-signs monitor. The PCB must reliably acquire and process heart rate, blood pressure, and respiratory rate signals, then pass the data to a microcontroller for further analysis and display. Here’s what I need from you: • Complete schematic capture based on my sensor and MCU selections • Four-layer board layout optimized for low-noise biomedical signals (Altium or KiCad preferred) • Manufacture-ready Gerber files, pick-and-place data, and a clearly structured BOM with medical-grade component choices • Design reviews at schematic and pre-release layout stages so we can make sure the board meets IEC 60601-1/-2 spacing, leakage, and isolation requirements • Brief ...

I am looking for someone to develop hardware on my request, it will be simple projects as seen on you tube. I am interested to know hourly rates, if I provide the hardware and code they would just need to wire them up. Would be nice to have someone from India NCR.

I need an expert to establish communication between two Siemens S7-1500 PLCs using OPC UA. Requirements: - Send digital, analog, and alarm signals. - Control a program on the server PLC via the client PLC. - Transmit maintenance data. Ideal skills and experience: - Experience with Siemens S7-1500 and OPC UA. - Proficiency in handling digital, analog, and alarm signals. - Strong background in PLC programming and communication protocols. Please provide relevant work experience in your bids.

The task is to design a compact PCB that drops straight into an SCX 1/32 car so it can run on a digital track. I want the board to read the track’s reed-sensor signal, let me assign any of 20 unique car IDs in firmware, and expose a surface-mount USB-C port on the edge for easy flashing once the body shell is back on. Size must stay close to the original analogue board footprint (about 24 × 18 mm, height under 6 mm) but I can adapt mounting holes or connector positions if you have a cleaner layout idea. Power comes from the standard track pickups (nominal 14–18 V DC), so include an efficient buck or LDO to feed the microcontroller and reed circuitry. I haven’t locked the MCU yet; pick anything small, inexpensive, and easy to program—ATmega, STM32, ESP32, or s...

We have an existing 6-axis driver for our plotter. We need to build a simple web interface where users can upload pictures for the plotter to draw. The system uses stepper motors with encoders and limit switches for XYZ axis. Key Requirements: - Web interface for image upload - Image-to-G-code conversion pipeline - Plotter communication and control - Support for stepper motors with encoders and limit switches - Testing and final tuning Skills Required: Python, Embedded Linux, C#, Firmware Development This is an ongoing project, estimated 1-3 months.

I’m updating the firmware for an STM32-based design and need an experienced C++ developer who is comfortable inside STM32CubeIDE. The codebase already compiles and runs on the microcontroller, but several features still require clean, well-structured implementation, performance tuning and thorough testing directly on the hardware. You’ll be working exclusively with STM32 microcontrollers; no FPGA or other targets are involved. Please be ready to pull the current CubeIDE project from my repository, build it as-is, and then extend it in C++17 (or later) while respecting the existing HAL layer and project structure. Deliverables • Updated CubeIDE project with the new or fixed functionality fully integrated • Clear build instructions and a short change log so I can ...

I need a Zigbee Green Power device for indoor lighting control. The primary features required are on/off switching and dimming. Key requirements: - Zigbee Green Power technology - Indoor installation - On/off switching and dimming capabilities Ideal skills and experience: - Familiarity with Zigbee technology - Experience in lighting control systems - Electrical installation knowledge for indoor environments

I’m kicking off a series of manufacturing-plant automation upgrades and I need a seasoned controls engineer who can run each project from the first I/O list through customer hand-over. You’ll design, program, and optimise complete PLC, SCADA and HMI architectures, keep schedules and costs on track, and be the face of technical support for the plant team once we go live. What the work looks like • Project scope reviews with our operators and maintenance crew • Writing and testing PLC logic, building SCADA dashboards and HMI screens, then carrying that code through FAT, SAT and on-site commissioning • Coordinating panel builders, electricians and any specialty subcontractors while managing the overall timeline and spend • Driving QA/QC for every drawi...

I need an ebike throttle limiter that sits between the ebike throttle ( running 5v red, black (gnd) and white control wire and its controller : (DO NOT CUT these) Throttle RED (+5V) ------------------------------------ Controller RED (+5V) Throttle BLACK (GND) ------------------------------------ Controller BLACK (GND) (ONLY cut/switch the WHITE signal) Throttle WHITE (signal) ----+-----------------------------> Switch T1 | +----[ Rseries 1kΩ ]----+-----> Switch T2 = LIMIT NODE | +-----> Pot BLACK (wiper) Pot RED ---------------------------------------------> Controller...

我想用一块 ESP32 搭配 INMP441 数字麦克风和 MAX98357A 扩音模组，做一个能“听得懂、说得出”的小型语音 AI。场景非常基础：与人进行简短对话，并可通过语音指令开关雾化模块即可，不需要复杂的物联网整合。 核心功能 • 语音识别：本地或云端均可，只要稳定； • 语音合成：中文语音播放，音质无需高保真； • 故障检测：当雾化模块或语音链路异常时给出语音或串口提示。 期望成果 1. 可直接烧录到 ESP32 的完整源码（Arduino IDE 或 ESP-IDF 均可）。 2. INMP441、MAX98357A、雾化模块的接线图与电源注意事项。 3. 简易指令表（如“开始雾化 / 停止雾化 / 查询状态”）及触发话术。 4. 编译、烧录与测试步骤说明，确保我按步骤即可复现。 若你能提供额外的调音参数、噪声抑制建议或 OTA 升级预留接口，我也非常欢迎。

JD – ROS Engineer Job Summary We are looking for a Software Engineer with strong experience in ROS (Robot Operating System) and C# to design, develop, and maintain robotic and automation software solutions. The role involves working on robot control, system integration, and real-time applications while collaborating closely with hardware, controls, and systems teams. ________________________________________ Key Responsibilities • Design, develop, and maintain robotic applications using ROS • Develop and support backend and application logic using C# • Integrate ROS-based systems with higher-level applications and user interfaces • Implement and maintain robot control, navigation, and communication nodes • Work on sensor integration, data handling, and real-t...

I need help building a working prototype of a small interactive toy. The prototype requires: A pop-up mechanism (using solenoids, springs, and/or small motors). Integration with Raspberry Pi or Arduino for control. Wiring/programming to operate the mechanism. A simple phone/web app to trigger the toy remotely. Requirements: Experience with mechanical design and prototyping. Hands-on skills with Raspberry Pi/Arduino electronics. Must show past project work (photos, CAD, or GitHub). Signed NDA. Deliverable: A working physical prototype (not just design files) that demonstrates the pop-up mechanism controlled by Raspberry Pi/Arduino. Budget: Budget will be discussed based on scope and experience. Please provide: What’s your estimated cost? How did you arrive at that numbe...

I am looking for an experienced RF hardware designer to consolidate and miniaturize an existing RF system based on a MYIR Zynq-7020 board. The current setup includes: 1. MYIR Zynq-7020 board (fixed, no redesign) 2. Adapter board 3. Two separate RF transmitter boards The goal is to integrate the two RF boards and the Adapter board into a single compact adapter board, while keeping the existing electrical interfaces to the MYIR board unchanged and minimizing or avoiding FPGA/firmware changes as much as possible. Scope of Work (High Level) - Integrate two RF transmit chains on one board - Use a shared reference oscillator and PLL for both RF paths - Replace discrete RF filters with compact off-the-shelf RF filters - Replace legacy power regulators with modern, small LDOs - Add RF routing op...

I’m building a mini ventilator—an embedded medical device combining mechanical and electrical subsystems—and I’m looking for a dependable partner who can translate detailed specifications into working hardware and firmware. Your responsibilities will include hardware design, firmware development, and end-to-end integration and testing. How we’ll work: • I’ll provide clear, itemized requirements; you’ll convert them into schematics, PCB layouts, and clean, well-documented firmware. • We’ll maintain a tight feedback loop with regular progress updates, clarification where needed, and rapid iterations after reviews. • Accuracy, reliability, timelines, and strict confidentiality are non-negotiable. Expected deliverables (as appli...

I’m building a small bionic butterfly that “flips” in mid-air, powered by an ESP32-S3 Super Mini. What I still need is the full control system: firmware for the board plus a cross-platform mobile app that drives two micro-servos through a joystick interface. Here’s the flow I’m picturing: • The ESP32-S3 runs custom firmware (Arduino IDE or ESP-IDF—whichever you prefer) advertising itself over BLE. • The mobile app—working on both Android and iOS—connects, shows a virtual joystick, and streams position data in real time. • The board translates that data into precise PWM signals so each servo can beat the wings smoothly and synchronously. I will supply the hardware (ESP32-S3 Super Mini and servos) for your testing if nee...

I need an experienced PLC programmer to develop a process control system using ABB AC500 PLCs. The programming should be done in Ladder Logic (LD). Key Requirements: - Expertise in ABB AC500 PLCs - Proficient in Ladder Logic (LD) - Experience with process control systems Ideal Skills: - ABB certification or equivalent experience - Strong background in industrial automation - Problem-solving and debugging skills Please provide relevant experience and any certifications.

I have individual, validated firmware blocks for the STM32L432KBU6 that handle an LIS3DH accelerometer (interrupt-driven), an EM4095 RFID front-end, the MCU’s internal touch-sensing controller, and a UART-based E220-400T22S LoRa module. My next step is to merge these routines into one cohesive, ultra-low-power application on our custom PCB. Power optimisation is the top priority. I want the system to remain in STOP mode most of the time, waking through the LIS3DH interrupt and periodic RTC events. When active, each peripheral must communicate reliably without compromising the sleep budget. Key points • Integrate existing C-based drivers into a single project • Configure and test the STOP-mode strategy, ensuring wake-ups from both the LIS3DH and the RTC function every t...

Hello , I need a complete design for a compact consumer-electronics board that revolves around a PIC microcontroller. The scope spans three tightly-linked parts: • PCB hardware – Produce the schematic and multilayer layout in Altium Designer, include all libraries you create, and deliver the full manufacturing package (Gerbers, drill files, pick-and-place, and a PDF schematic). • MCU firmware – Write well-commented code in MikroBasic (or another PIC-friendly tool if you justify the switch). The firmware must read multiple sensors, exchange data through an efficient serial protocol, and use smart power-saving modes to stretch battery life. Please supply project files, compiled HEX, and a short flashing guide. • PC interface – Build a Windows utility in VB....

I need a complete design for a compact consumer-electronics board that revolves around a PIC microcontroller. The scope spans three tightly-linked parts: • PCB hardware – Produce the schematic and multilayer layout in Altium Designer, include all libraries you create, and deliver the full manufacturing package (Gerbers, drill files, pick-and-place, and a PDF schematic). • MCU firmware – Write well-commented code in MikroBasic (or another PIC-friendly tool if you justify the switch). The firmware must read multiple sensors, exchange data through an efficient serial protocol, and use smart power-saving modes to stretch battery life. Please supply project files, compiled HEX, and a short flashing guide. • PC interface – Build a Windows utility in VB.NET ...

Abstract: Manufacturing-Ready 130nm CMOS Inverter Design The objective of this project is to design, verify, and prepare a standard CMOS inverter for fabrication using the SkyWater 130nm Open-Source PDK. Unlike theoretical projects, this work follows a complete "Silicon-to-GDS" flow. The process begins with Schematic Capture and Pre-Layout Simulation to establish electrical baselines. This is followed by Physical Layout, where the geometric structures of the NMOS and PMOS transistors are manually drawn according to strict foundry Design Rule Checks (DRC). The design is then validated through Layout vs. Schematic (LVS) to ensure physical-electrical equivalence. Finally, Parasitic Extraction (PEX) is performed for Post-Layout Simulation to account for real-world wire resistance and...

Overview I’m looking to develop a robust UART to UDP bridge on STM32 for handling large binary frames and NMEA data. The aim is to enhance data transmission reliability between devices. Scope of work - Develop a UART RX system with DMA and ring buffer on STM32 for lossless data reception. - Implement UDP TX using LWIP for sending data over UDP with configurable IP and port. - Handle large frames by sending in single datagram or using fragmentation protocol (frame_id, chunk_index, total_chunks, crc) for payloads around 10KB. - Optional: forward NMEA data on a separate UDP port. - Deliver complete CubeIDE project and documentation. - Test and verify UDP reception with log/pcap/wireshark or video to prove valid frame transmission. Additional information I’ll accept delivery a...

I already have a working PCB built around an Xsens MTi-630 IMU and an NXP MKV56 microcontroller. What I need now is a technician who can revise the existing firmware so the remote camera head delivers rock-solid motion compensation on set. Your task is to design and embed a custom sensor-fusion routine that blends gyro, accelerometer, and magnetometer data from the MTi-630, then feed that fused orientation into the motor-control loop over CANopen. I’m aiming for a balanced mix of speed and accuracy so operators never feel lag yet still enjoy drift-free performance during long takes. You will be starting from my current codebase (MCUXpresso / NXP SDK), which already handles basic hardware abstraction and CANopen messaging. The focus is on: • Writing or adapting a quaterni...

I need an experienced electronics/PCB engineer to design a reliable, 24/7-operating traffic light controller PCB. This is a safety-critical system (not a hobby project). SYSTEM: • MCU: ESP32 • Load: 220VAC traffic light LED modules • Outputs: ~19 relay-controlled channels • Operation: Continuous (24/7) RELAY CONTROL: • Relay outputs driven via 74HC595 shift registers (SPI-style) • 3 × 74HC595 chained • OE pin must have hardware pull-up (outputs OFF at boot) • ESP32 enables outputs only after startup • Relay drivers with proper flyback protection FAILSAFE / SAFETY: • Master relay/contactor that cuts power to ALL lamp outputs • Must drop on: - ESP32 crash - Watchdog timeout - Power instability • Safe power-up and fail...

I’m building a piece of system-level software and need a seasoned developer for a small project for less than 20 hours. We offer ratings for stocks and bonds, ETFs, based on their rate, month and discounted rating price. Rates are: 2, 3, 4, 5. Months are: 6, 12, 24, 36, 48, 60 - List all stock in a web page NYSE. Web page is scalable for phones and desktops. - Create a rating, rate, month list for each stock. - Run the listing on an alphabetical listing in phone (iPhone 10-17). - By loading the list the app become available on the phone offered as a deck icon. Send link for testing on phone. - Create application software for this listing on a phone for AppStore. Set app for AppStore account. Milestone 1. Ready linked (url) approved content view on phone and desktop. Milestone...

Je souhaite développer un système embarqué destiné à l’automatisation domestique. L’objectif est de concevoir une carte compacte capable de dialoguer, via des modules de communication sans fil, avec divers capteurs et actionneurs déjà présents dans la maison ou ajoutés ultérieurement. Le travail inclut la phase matérielle (schéma et PCB), le développement du firmware et les tests de communication. Les protocoles sans fil à privilégier (Wi-Fi, Bluetooth Low Energy, Zigbee, etc.) pourront être définis selon la portée, la consommation et l’interopérabilité requises. Livrables attendus : • Schéma électronique complet e...

The goal is straightforward: as soon as an ESP device is present—whether connected over Wi-Fi or broadcasting in monitor mode could be spotted in hidden places

Necesito integrar cancelación de ruido activa (ANC) en mis protectores auditivos 3M PELTOR X2, pensados para un entorno industrial. El objetivo es que el nivel de ANC pueda regularse mediante un control manual fácilmente accesible en el propio casco y que todo el sistema funcione con baterías recargables para evitar el uso de pilas desechables. Busco a alguien con sólida experiencia en electrónica de audio que pueda: • Diseñar el esquema electrónico y la PCB necesaria para añadir micrófonos, etapa de procesamiento y amplificación. • Incorporar un potenciómetro o selector físico que permita subir o bajar la intensidad de cancelación. • Prototipar y probar el sistema directamente so...

ATLANTIS OTA UPDATE SYSTEM – DEV PROMPT (WIFI TEST FIRMWARE) Objective Implement a production-grade OTA firmware update system for Atlantis controllers that is safe, rollback-capable, power-loss tolerant, and integrates with Blynk NCP (ESP32 runs unmodified NCP firmware). Deliver test firmware that validates the entire OTA lifecycle over Wi-Fi before Blynk integration. System Overview Hardware Primary MCU: STM32H723VIT6 (main firmware; Arduino sketch runtime) Connectivity MCU: ESP32 running Blynk NCP binary (not modifiable) Dealer flashing: Android Dealer Toolkit via USB-C UART, toggling BOOT0 + NRST, using STM32 ROM bootloader Dealer flashing is force-install / recovery Dealer flashing does NOT interact with running firmware Dealer flashing does NOT write OTA metadata Non-Negotiabl...

Ich möchte mit dem „BBC micro:bit mit Kitronik Inventor’s Kit“ zwei kleine Experimente umsetzen und suche dafür eine komplette Dokumentation in Video-Form: 1. Aufgabe A – Sonnen-Ventilator • Bei Helligkeit soll ein Ventilator anlaufen, bei Dunkelheit stoppt er. 2. Aufgabe B – Taster-Licht • Drücke ich Taste A, geht eine LED an und schaltet sich nach exakt 2 Sekunden wieder aus. Lieferumfang, den ich von dir erwarte • Ein durchgängiges Video-Tutorial (Schritt für Schritt, klar erkennbar gefilmt) vom Aufbauen auf dem Breadboard bis zum Testen der beiden Schaltungen. • Mindestens drei scharfe Fotos der fertigen Verdrahtung aus unterschiedlichen Winkeln. • Eine kurze, anfängerfreundliche Er...

For my current university project I have to build a compact PCB whose only job is to collect data from several temperature sensors and route those readings to the rest of my prototype through simple wired connectors. Everything must be laid out and modelled inside Fusion 360, right down to the housing that will protect the board once it is fabricated. Here is what I need from you: • Create the full schematic and board layout in Fusion 360’s electronics workspace, optimised for straightforward sensor-integration and robust wired headers. • Export clean Gerber/Drill files plus the native Fusion 360 design so I can iterate later. • Model a 3-D printable enclosure in the same project file, dimensioned precisely to the finished PCB, with openings for the temperature-...

I want to turn my stock WowWee MiP into a fully-independent companion with far more capability than the original phone-controlled toy. The big push is to give it functional robotic arms—servo-driven, proportional, and strong enough to perform simple pick-and-place demos—while keeping the self-balancing chassis intact. To drive everything, I need an internal “brain” (Raspberry Pi, ESP32, or another MCU you’re comfortable with) that can: • run onboard code without any phone connection • store multiple programs in flash so I can swap behaviors on the fly • process a forward-facing camera for navigation and object tracking • handle voice-command triggers and speak back in character using a small speaker For interaction I’m l...

Necesito ayuda puntual para afinar un proyecto existente sobre ARM STM32. El hardware ya cuenta con: • Protocolo de comunicación binario implementado • Dos tiras WS2812 de 60 LEDs cada una, controladas de forma independiente • Módulo RFID PN532 • Conjunto de switches de entrada Mi prioridad ahora es la integración del RFID y los switches; los obstáculos que enfrento son Problemas de software. Quiero que ambos elementos se lean de forma fiable y se enlacen correctamente con el resto de la lógica ya programada. Busco a alguien con demostrable Experiencia en: – Desarrollo sobre microcontroladores STM32 (bare-metal o HAL). – Manejo de periféricos I²C/SPI, interrupciones y temporización precisa. ...

I'm looking for an experienced programmer to develop RF modules based on MTK chips. The primary functionality required is signal reception, specifically for digital signals. This project extends to firmware modification for new hardware of the F21 Pro model, adapting it to work with US bands and ensuring wide usability. Key Requirements: - Modify NV data in the firmware to suit the new chipset (likely running on LWTG) and adapt this file for US band compatibility. - Ensure the firmware can be flashed easily to multiple phones and that a complete backup source file is provided. - Conduct thorough compatibility testing for the firmware. Ideal Skills and Experience: - Strong background in RF engineering and programming. - Expertise with MTK chipsets and NV data modifications. - Experie...

Job Description:- We are a registered company coordinating academic projects in the Embedded / ECE domain for Indian universities. We are looking for one reliable freelance Embedded Systems developer for long-term, project-wise collaboration. This is not a full-time job. Work will be assigned per project. Scope of Work Develop Embedded / ECE hardware or simulation-based projects Support domains like: Embedded Systems, IoT, ARM / Microcontrollers FPGA / VLSI (optional) Control systems / Sensors / Automation (as applicable) Deliverables per project: Working code / simulation / hardware logic Result screenshots / output proof Project report content (chapter-wise) Project PPT content IEEE conference paper draft Scopus journal extended paper draft Support 1–2 rounds of re...

I'd like to create a schematic and PCB layout that I can use to print from a photo I have. The layout is based on an ATmega and an ESP32, along with a servo connected to the ATmega. I'd like a guide on how to create a schematic file that I can modify and use in the future, not just the photos I have.

I have a production-ready, IGBT full-bridge welding inverter that already powers both TIG and MMA processes, yet the embedded side still needs a final expert pass before release. The control board is built around 8051 and STC MCUs running Keil C51 firmware, and every line of code directly shapes arc stability, HF start, AC balance, soft-start, and safety interlocks. The short-term goal: review, tidy, and extend the existing code so it drives the power stage flawlessly in TIG and MMA, AC and DC. That means refining PWM timing, gate-drive dead-time, current-feedback filtering, and all the little state-machine details that separate a decent welder from a great one. Core tasks and deliverables • Audit the present C51 codebase, flagging race conditions or timing pitfalls. • Im...

Project: Calling / Video Conferencing App (Zoom-like) We are looking for an experienced developer/team to build a calling and video conferencing application similar to Zoom for web and mobile platforms. Core Requirements: One-to-one and group audio & video calling Real-time conferencing with low latency User authentication & meeting management (create, join, schedule) Screen sharing feature Chat during meetings Call controls (mute, video on/off, end call) please share me your samples work this is big client

I need a clean, production-ready PlatformIO project for the Nordic nRF51822 written in C/C++. The example must boot, scan for nearby BLE devices, connect to one of them, and exchange plain text strings—ideally via a Nordic UART–style GATT service. Please build it around a SoftDevice or Nordic SDK you have already proven on real hardware; I do not want AI-generated scaffolding that compiles but fails at runtime. The code should: • compile inside PlatformIO with a single pio run command • flash successfully to an nRF51822 DK or compatible module • start scanning, connect on the first match, and perform a two-way text message exchange • cleanly disconnect and resume scanning Deliverables I’ll review: 1. A complete PlatformIO project folder (ma...

I aim to develop a solution that will facilitate data communication between an Arduino UNO and a SIM7600E using AT+COMMAND. The primary data in focus will be temperature sensor readings. Key Responsibilities: - Setting up a reliable connection between Arduino UNO and SIM7600E - Implement AT+COMMAND for effective communication - Design a protocol for transmitting temperature sensor data Ideal Skills: - Solid knowledge of Arduino - Proficiency in handling SIM7600E - Experience in implementing AT+COMMAND - Understanding of sensor data transmissions. Please ensure you can efficiently deliver on these requirements, and provide the mentioned sensor data communication before placing your bid.