
In Progress
Posted
Paid on delivery
I have a finished board that currently carries a Micro-USB connector. I now need that footprint, schematic, and routing swapped to a USB Type-C receptacle so the product can handle both power and low-speed USB 2.0 data with the plug inserted in either orientation. The present design’s data path is only USB 2.0 low-speed, so D+ and D- simply need to be bridged to both sets of A/B pins on the USB-C side. What I do need added are the correct CC1/CC2 pull-down resistors so the port negotiates 5 V power in either direction, plus any layout tweaks to keep impedance and clearances clean. No high-speed differential routing or USB-PD controller is required—just solid compliance for reversible 5 V, 1A operation and reliable data transfer at the existing low-speed rate. You will receive the current schematic and PCB file (KiCad). After the modification I will need: • Updated schematic with the new Type-C connector and CC network • Revised PCB layout ready for fabrication • Regenerated Gerber/ODB++ and pick-and-place data • A brief note highlighting any mechanical keep-out changes or BOM updates I’ll review the files in KiCad; if the board can be manufactured and the port enumerates correctly in both orientations on my test jig, the job is done.
Project ID: 40800323
29 proposals
Remote project
Active 6 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs

Hi, I can modify your existing KiCad design to replace the Micro-USB connector with a USB Type-C receptacle while retaining the existing functionality. I'll update the schematic, add individual 5.1kΩ CC1/CC2 pull-down resistors, correctly map D+/D− for reversible USB 2.0 operation, and adjust the PCB routing, grounding and clearances. I have experience designing ESP32-based boards, USB interfaces, power management circuits and compact PCBs using KiCad. Deliverables: - Updated schematic and PCB files. - DRC-checked, fabrication-ready layout. - Gerber/ODB++ and pick-and-place files. - BOM updates and mechanical change notes. I'll review the existing design first to ensure the modification is clean and doesn't affect other board functionality.
₹2,000 INR in 2 days
0.0
0.0
29 freelancers are bidding on average ₹6,807 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹7,000 INR in 7 days
7.5
7.5

My PCB design and circuit-design background makes me well suited to upgrade your existing Micro-USB board to a reversible USB-C interface without adding unnecessary USB-PD complexity. I can work with the supplied KiCad design to replace the connector footprint and schematic, bridge the USB 2.0 D+/D− connections appropriately, and add the required CC1/CC2 pull-down network for 5 V power operation. My experience covers electronic design, PCB layout, embedded systems, and manufacturer CAD files, including power boards, SMPS boards, AC/DC and DC-DC converters, battery chargers, and low-speed embedded applications. This is directly relevant to preserving clean routing, suitable clearances, reliable power connections, and practical fabrication output. I can provide the revised schematic and PCB, regenerated Gerber/ODB++ and pick-and-place files, plus a concise summary of BOM and mechanical keep-out changes. I am ready to make this USB-C revision clean, manufacturable, and suitable for low-speed USB 2.0 operation in either plug orientation.
₹12,500 INR in 7 days
7.5
7.5

Your existing KiCad board can be upgraded cleanly by leveraging my 8+ years of professional PCB design experience with KiCad, Altium, Eagle, and EasyEDA. As a verified Electrical/Electronics Engineer and Preferred Freelancer, I can handle the USB-C footprint replacement, schematic updates, CC1/CC2 pull-down network, reversible USB 2.0 D+/D− connections, and the required PCB layout adjustments. My background in circuit design, electronics, PCB layout, and embedded systems is directly relevant to maintaining reliable 5 V power and low-speed USB data while preserving practical clearances and manufacturability. I will provide the revised KiCad schematic and board files, regenerated Gerber/ODB++ and pick-and-place outputs, plus a concise note covering mechanical keep-outs and BOM changes. I am ready to apply my PCB design expertise to this USB-C upgrade and deliver fabrication-ready files for your review. Choose me for a careful, professional modification of the existing design.
₹7,000 INR in 7 days
6.9
6.9

Hi there, I carefully reviewed your requirement to replace the existing Micro-USB interface with a reversible USB Type-C receptacle while preserving the current USB 2.0 low-speed data path and 5 V / 1 A power functionality. I am a mechatronics engineer with almost half a decade of experience in embedded electronics, PCB design, hardware prototyping, and interfaces such as USB, UART, SPI, I2C, and similar embedded systems. My background is directly relevant to updating the connector circuitry, CC configuration, routing, footprints, and manufacturing outputs without unnecessarily changing the rest of the finished design. Because USB interfacing and PCB layout are already part of my core skillset, I can approach the modification efficiently while paying attention to reversible D+/D− connectivity, CC1/CC2 implementation, mechanical clearances, footprint accuracy, and fabrication readiness. Please send me a message so we can discuss the project and start. Best regards, Samuel tshibangu
₹7,000 INR in 1 day
6.6
6.6

Hello, I am an experienced PCB layout designer and can help replace your existing Micro-USB connector with a USB Type-C receptacle. I can update the schematic, add the correct CC1/CC2 pull-down resistors, connect the USB 2.0 D+ and D− signals for reversible operation, and modify the PCB routing while maintaining proper clearances and layout quality. I will also prepare the revised PCB layout, Gerber/ODB++ files, pick-and-place data, and updated BOM. Please share your existing KiCad schematic and PCB files so I can review the design and confirm the required changes and delivery time. Best regards, PCB Design Engineer
₹12,500 INR in 3 days
6.4
6.4

Hey there! I’m Alok, A PCB, Circuit and Mechanical designer with a passion for turning ideas into rock-solid, high-performance circuit boards. even expert on Python, C, C++ With nearly a decade of experience, I’ve tackled everything from compact consumer gadgets to complex industrial systems—always with a focus on precision, efficiency, and reliability. # Schematic & Layout Design – Clean, optimized, and manufacturable. # Component Selection & Library Management – No surprises, just the right parts for the job. # Reverse Engineering – PCB cloning, replication, and improvements. # Gerber, BOM & CPL Generation – Ready for seamless production. # DFM & DFA Expertise – Because great design means smooth manufacturing. # Multi-Layer, Flex, & High-Density PCB Design – Whatever the project needs. If you need a PCB and Code that’s efficient, reliable, and built for real-world performance, let’s chat. I’d love to help bring your project to life!
₹8,800 INR in 7 days
6.0
6.0

PCB layout and circuit design are directly aligned with this USB-C upgrade, and my electronics and embedded-systems skills support the practical requirements of a reversible 5 V USB 2.0 connection. I can work from your existing KiCad design to update the connector footprint, schematic, routing, and supporting PCB details. The required CC1/CC2 pull-down network, duplicated D+/D− connections for both USB-C orientations, clean clearances, and low-speed USB routing all fit within my circuit-design and PCB-layout capabilities. I can also provide the revised fabrication outputs, pick-and-place data, and a concise note covering mechanical keep-outs and BOM changes. I would be glad to modify your board carefully and deliver KiCad files ready for review and manufacturing.
₹5,100 INR in 1 day
4.8
4.8

HI, I am an experienced electronics and PCB Design engineer, specialised in use of ECAD software such as Altium Designer, KICAD, EasyEDA, etc. for the the design of electronics and PCB. I will design your projects to meet your Requirements and the industry standard. I do all kinds of circuits such as Power delivery circuit, Sensor Integrated Circuits, wireless control, MCUs etc. I will deliver the following. The Schematics for your Design The PCB for the design Bill of materials(If needed) Gerber, Pick and Place and other manufacturing and assembly drawings needed. Full Support and consultancy till the project is done. Kindly send me message for my previous designs and also so we can discuss further on your project I look Forward to working with you. Best Regards, Abdur-Rafiq
₹7,000 INR in 7 days
5.3
5.3

Custom IoT hardware, PCB design, and ESP32/STM32 firmware are core parts of my work, making me well suited to review your ESP32 board before fabrication. My background in circuit design, electrical engineering, electronics, and PCB layout allows me to assess the complete physical design—not just whether the schematic is electrically correct. Recently completed work similar to your projcts: https://www.freelancer.com/projects/electronics/KiCad-PCB-Layout-Optimization/reviews
₹7,000 INR in 7 days
5.1
5.1

Hi There! As you can see in my portfolio—accessible via my profile—I have extensive experience in designing PCBs and equipment for mass production. I am well-equipped to handle your requirements, including the integration of a robust, industry-standard USB-C connector, such as the GCT USB4105. Unlike many of the other proposals you might encounter here, this one is not AI-generated. I look forward to hearing from you so we can discuss a more accurate quote. Best Regards!!
₹5,000 INR in 3 days
4.8
4.8

Hello, I’m an experienced Hardware and PCB Design Engineer with hands-on experience in KiCad, schematic modification, USB interfaces, and production-ready PCB design. I can modify your existing Micro-USB design to support a USB Type-C receptacle while maintaining the existing USB 2.0 Low-Speed functionality and 5V/1A power input. My work will include: - Replacing the connector in the schematic and PCB. - Implementing the correct CC1/CC2 5.1kΩ pull-down resistors. - Connecting the USB 2.0 D+/D- pins for reversible operation. - Updating PCB routing and checking clearances. - Verifying the connector footprint and mechanical dimensions. - Delivering updated KiCad files, Gerber/ODB++, BOM, and pick-and-place files. I will also review the existing power path to ensure it can safely support the 5V/1A requirement. I can start by reviewing your current KiCad files and identifying the required changes before proceeding with the modification. Best regards,
₹7,000 INR in 7 days
3.8
3.8

My hands-on embedded systems and USB experience make me well suited to upgrading your existing KiCad board from Micro-USB to a reversible USB-C receptacle. I can handle the circuit and PCB changes needed for USB 2.0 low-speed data and 5 V power, including bridging D+ and D- to the appropriate USB-C pins and adding the required CC1/CC2 pull-down network. My skills in circuit design, electronics, PCB layout, and microcontroller-based hardware support a practical board-level update rather than a purely schematic change. I will revise the connector footprint, routing, clearances, and related BOM items while preserving the existing low-speed USB path and checking the layout for reliable fabrication. I can also provide the updated KiCad files, regenerated Gerber/ODB++ and pick-and-place outputs, plus a concise note covering mechanical keep-outs and BOM changes. Choose me to make this USB-C conversion clean, manufacturable, and ready for your orientation and enumeration testing.
₹3,500 INR in 7 days
3.4
3.4

I have experience in PCB design, motion control circuits, and electrical isolation. I have a dedicated hardware lab for testing and validation. I'd be happy to explain my previous projects and share relevant work examples. Here's what I bring to this: → I rebuild the Type-C footprint and route D+/D- to both A and B pin sets with 5.1k pull-downs on CC1/CC2 for proper 5V 1A sink negotiation → I've shipped custom USB and connector-level reworks on ESP32 and STM32 boards, so impedance and clearance tweaks are routine → Full in-house capability: schematic, PCB layout, and regenerated Gerbers, ODB++, and pick-and-place from your KiCad files → I keep your existing form factor and flag any mechanical keep-out or BOM changes in a short handover note My approach: → Review your KiCad schematic and PCB, confirm the footprint and CC network against the receptacle datasheet → Swap the connector, bridge D+/D- across A/B pins, add CC1/CC2 pull-downs, and clean up routing and clearances → Regenerate fabrication and assembly files, then note keep-out and BOM deltas for your jig test For this scope, the cost would be ₹7000. Happy to walk you through my approach and past connector rework on a chat.
₹7,000 INR in 2 days
3.5
3.5

Hello, Your requirement is change of connector, which can easily be handled along with needed addition of CC pull-down resistors. In addition to connector, I can help review your rest of layout also. I have made several industrial products. I carry 20+ years of design & development experience. I specialize in precision & low noise analog, sensor signal conditioning, EMI-EMC, low power electronics, power supplies, high speed & long-life battery IoT products. Please see my works & profile below, https://www.freelancer.in/u/JagdishCK I will re-route the changes in PCB (or other sections which we can discuss) & provide you layout as per EMI-EMC guidelines & handover final schematic, layout, BOM, etc & other package in Kicad. Please message me for more discussions. Regards, Jagdish Karamchandani
₹8,000 INR in 5 days
3.0
3.0

Hello, I can update your existing KiCad design from Micro-USB to USB Type-C while preserving the USB 2.0 low-speed functionality. The work will include selecting a suitable USB-C receptacle, updating the schematic with separate 5.1 kΩ CC1/CC2 pull-down resistors, connecting the duplicated D+/D− pins correctly, and revising the PCB routing and connector placement. I will also review the 5 V power path, connector mechanical dimensions, and manufacturing clearances, then deliver the updated KiCad files, Gerbers, BOM changes, and pick-and-place data. Before starting, I would like to confirm whether the USB-C port is power-input-only and whether the existing board outline and enclosure dimensions must remain unchanged. I can provide a short technical summary of the modifications and ERC/DRC results with the final delivery. Thank you.
₹9,000 INR in 6 days
3.1
3.1

I have experience in PCB design, schematic modifications, USB interfaces, and embedded hardware development. I can help upgrade your existing Micro-USB design to USB Type-C and provide manufacturing-ready files. I would also be happy to share details of my previous relevant projects so you can review my work. Swapping a Micro-USB to Type-C on a finished board is mostly about getting the CC network and the reversible D+/D- bridging exactly right, and I'd love to help you get this clean the first time. Here's what I bring to this: → I've done USB-C retrofits on production boards where the CC1/CC2 5.1k pull-downs and A/B pin bridging had to enumerate correctly in both orientations on a test jig. → I work in KiCad daily, so I'll take your existing schematic and PCB directly, no format conversions or surprises. → Beyond the swap, I handle full hardware — PCB design, firmware, 3D enclosures, and prototype shipping — so if anything downstream needs attention, it's one conversation. → I can turn this around quickly and regenerate Gerbers, ODB++, and pick-and-place with a short note on keep-outs and BOM changes. My approach: → First I'll review your schematic and board, confirm the connector footprint and CC network fit your stackup. → Then I'll swap the connector, bridge D+/D- to both pin sets, add CC1/CC2 pull-downs, and tidy impedance and clearances. → Finally I'll regenerate fabrication files and send a brief note on mechanical keep-outs and BOM updates for your review.
₹3,000 INR in 2 days
3.1
3.1

Hi, I'm an electronics hardware engineer with around 2 years of experience working for a Japanese company, specializing in PCB schematic design, layout, and hardware development. I have practical experience with KiCad, multilayer PCB design, USB-C interfaces, power management circuits, and ESP32-based hardware. For your project, I can: - Replace the Micro-USB connector with a suitable USB Type-C receptacle. - Add the correct 5.1kΩ pull-down resistors on CC1 and CC2. - Configure D+ and D- connections for reversible USB 2.0 operation. - Review VBUS, GND, and power routing for 5V/1A operation. - Check footprints, clearances, signal routing, and mechanical keep-outs. - Generate updated Gerber, NC Drill, BOM, and pick-and-place files. I'll review your existing KiCad schematic and PCB files first, then make the necessary modifications while preserving the existing functionality. I'll also provide a brief summary of design changes and manufacturing considerations. I'm available to start once you share the project files. Looking forward to working with you! Best regards, Phuong
₹7,000 INR in 7 days
2.3
2.3

Hi, I'm an Electronics and Embedded Systems Engineer currently working at STMicroelectronics, with 5+ years of experience in electronics design, embedded systems, and PCB development. I have hands-on experience with KiCad and can help you replace the existing Micro-USB connector with a USB Type-C receptacle, including the updated schematic, CC1/CC2 pull-down network, reversible USB 2.0 data connections, and optimized PCB routing. I'll also provide the updated manufacturing files (Gerbers/ODB++ and pick-and-place data), along with a brief summary of any mechanical or BOM changes. I look forward to working with you!
₹3,000 INR in 1 day
1.0
1.0

My hands-on experience with KiCad schematic and PCB modifications makes me well suited to upgrade your existing Micro-USB design to a reversible USB-C interface. I work with electronic circuit analysis, component selection, PCB layout, and hardware validation, allowing me to address both the electrical and fabrication requirements of this change. I can update the schematic with the USB Type-C receptacle, connect the USB 2.0 D+/D− paths appropriately, add the CC1/CC2 pull-down network for 5 V operation, and revise the PCB layout with attention to routing, clearances, connector placement, and mechanical constraints. My experience interpreting datasheets and technical specifications will support correct component selection and reliable low-speed data and power operation. I can also provide the revised KiCad design files, regenerated fabrication and pick-and-place outputs, and concise documentation covering BOM or keep-out changes. Choose me for a practical, carefully reviewed PCB upgrade.
₹8,500 INR in 3 days
1.0
1.0

This is a straightforward swap. I'll replace the Micro-USB footprint with a Type-C receptacle, tie D+ and D- to both pin sets, add 5.1k pull-downs on CC1 and CC2, and re-route with proper clearances. You'll get the updated KiCad schematic and layout, fresh Gerbers and pick-and-place files, and a short note on keep-out and BOM changes within 3 days. I've worked on a lot of USB-powered boards and industrial electronics. Do you have a specific Type-C part in mind, or should I pick a common one?
₹4,500 INR in 3 days
0.5
0.5

Mangaluru, India
Member since Nov 3, 2026
£20000-50000 GBP
£750-1500 GBP
₹12500-37500 INR
₹600-1500 INR
₹1500-12500 INR
$10-20 SGD / hour
$30-250 USD
₹12500-37500 INR
$30-250 USD
$10-30 USD
$250-750 USD
₹750-1250 INR / hour
€30-250 EUR
$10-30 USD
£20-250 GBP
$10-30 USD
$30-250 USD
₹600-1500 INR
$750-1500 USD
$1500-3000 USD