Power Cutback & 4-Gang Install

@hayat38402

Hi, how are you doing? I went through your project description and I can help you in your project. your project requirements perfectly match my expertise. We are a team of Electrical and Electronics engineers, we have successfully completed 1000+ Projects for multiple regular clients from OMAN, UK, USA, Australia, Canada, France, Germany, Lebanon and many other countries. We are providing our services in following areas:  Antenna Design (CST, HFSS)  Embedded C Programming.  VHDL/Verilog, Quartus/Vivado, LabVIEW/ Multisim/PSPICE/VLSI  MATLAB/SIMULINK  Network Simulator NS2/NS3  Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC, STM32 and ESP32.  IDEs like Keil MDK V5, ATmel studio and MPLab XC8.  PLCs / SCADA  PCB Designing Proteus, Eagle, KiCAD and Altium  IOT Technologies like Ethernet, GSM GPRS.  HTTP Restful APIs connection for IOT Communications. Also, we have good command over report writing, I can show you many samples of our previous reports. Kindly consider us for your project and text me so that we can further discuss specifically about your project's main goals and requirements.

@bilalh585

I am Bilal, a 5+ years experienced electrical engineering professional, and I can assist with safely isolating the existing residential supply and installing the required temporary outdoor power arrangement. What I’ll deliver Safe identification and isolation of incoming/live feeds Verification of de-energised circuits using appropriate testing procedures Weather-rated exterior 4-gang outlet box installation Proper wiring with GFCI protection and clearly labelled breakers Code-compliant installation and testing Tidy workmanship and safe site handover Photos and a concise completion report I understand the importance of a verified zero-energy state before work begins and will prioritize safe isolation, correct testing, and compliance with applicable local electrical requirements. Where licensing or inspection sign-off is legally required, I’ll coordinate with the appropriately licensed electrician/inspector. Best regards Bilal.

@alyan056

Hi, Have you confirmed whether your local code requires a licensed electrician's sign-off before the inspection, or would you need help coordinating that alongside the GFCI install and panel lockout? https://www.freelancer.pk/u/alyan056 Alyan

@Aaleen110

The existing service being partially operational means the priority is isolating and de-energizing the entire property before any new work starts. I will locate all incoming live feeds at the panel or meter and terminate them, then use a non-contact voltage tester to confirm a zero-energy state throughout the building. Once that’s confirmed, I will run a code-compliant line from a suitable point, incorporating GFCI protection and clearly labelled breakers for the new 4-gang outlet box. This box will be weather-rated and mounted securely on the exterior wall, wired directly to the protected supply. The most likely failure point here is contamination of the de-energized state if a feed isn’t properly isolated, so I test at multiple points and then re-test immediately before connecting the new supply to the 4-gang box. What is the intended load for this temporary power source so I can size the incoming breaker appropriately? 10 reviews on Freelancer at 5.0, everything delivered on time and on the agreed price so far. I need confirmation of the electrical panel's location and access before I can provide a firm start date.

@edwina245

Hello, I have handled many residential electrical jobs, including safely isolating incoming service, verifying zero-energy conditions, and setting up GFCI-protected temporary power for renovation crews. I know what inspectors look for, so I can get this done safely and to local residential code the first time. I'll locate and terminate every live feed at the panel or meter, then test throughout the house to confirm a zero-energy state. Next, I'll mount a weather-rated 4-gang box on the exterior wall and run a short, code-compliant line to it with GFCI protection and clearly labeled breakers. After testing everything, I'll send you a short hand-over report with photos, and I can start within a few days and finish the work in one to two days. Thanks for reading my proposal. Edwin