arduino control board sketche connected to load cell

Load Cell signals:

50 Kg capacity load cell will monitor maximum load 300 N, or max 30.6Kg.f

It is 4 wire load cell will run on “Arduino uno” through “HX711 shield “ .

Needed sketch details write code clarifying pins connections on Arduino uno :

1- Interfacing mentioned load cell with 2mv/V output with Arduino through HX711 taking readings with highest possible rate “ex: every 1 millisecond ,or less ” >> displaying reading on LCD screen in N ,or KG.f with [url removed, login to view] resolution ,or 0.01 if possible. With filtered readings without noise.

2- With updated fast reading >>digital output signals according to value of reading as follows :

a) Reading increased from zero to just [url removed, login to view] ( adjustable) >> activates digital output1 (touching signal).

b) Exceeding limit of load cell designed capacity (330 N) ( adjustable) >>> activates (overload) digital output2 and alarm message on screen “overload “.

c) Peak value of successive continuous readings >> will activate( peak value ) digital output3 and message of hardness =” the reading of local peak ,or maximum load value ;as example : 65.1 N detected from successive readings 0,1,2,…………..63.5,64.6,65.1,64.4,30,20,11,0 ” >>>>store this peak value in memory as sample reading of hardness >>> display sample reading on LCD screen “hardness = 65.1 N “ .

3- Two Digital signals will be given {Digital input1 “ single “,and Dig-input2 “ Automatic batch “} :

a) Single sample mode will be displayed on screen and just having peak value it is ready on screen and ready to be printed.

b) Automatic batch mode will be displayed on screen and will ask user about Number of samples N ,and 12 digit Batch Number entries? And internal counter will count till reaching end of batch at N samples storing all samples values on memory preparing it for printing and statistics( avoid power failure data losses when you store results).

4- Printing samples readings ,or peak values on normal printer ,or thermal ( clarify printer type and connection please ) including :

a) its readings basic statistics { average ,min, maximum, standard deviation }

b) Enter and Print Date and Time to the report.

c) Enter a 12 digit Batch Number label appears on display and in printed report.

d) Calibration report at three points 5, 10, and 15 Kg.f.

e) Print-out of force increase curve vs time for samples.

f) Display: LCD Display for No. of samples, and hardness, or peak value results.

g) Keyboard: Numerical and function keys.

h) Number of tests prior to statistic: Up to 250.

5- Calibration menu for the hardness test station at any desired point as piece-wise linear method.

6- LCD display and optical keypad board Interface.

Aptitudini: Arduino, Electronică, Software încorporat

Vezi mai multe: cell gridview control net, casino control board links html, speed motor control board, cell connected asterisk usb, sqlserver2005 database connected treeview control aspnet, cell phone camera control app win, visual basic loop read next cell cut paste, load sql binary webbrowser control 2008, cell phone buyer vbulletin board, wiring diagram control board sps system, load pdf file webbrowser control save sql vbnet, vsto excel read write cell, read excel cell, cell phone control helicopter, read part cell excel macro, hot shot load info board, logo bangladesh cricket control board, macro read contents cell, converter load cell, load cell avr, inventory control board vbnet, macro read data cell excel, shoutcast control board, application cell phones gsm control electrical applications project, interface load cell rslogix 5000 plc

Despre angajator:
( 0 recenzii ) Egypt

ID proiect: #11911957

19 freelancers are bidding on average $281 for this job

155$ USD în 3 zile
(52 Recenzii)

A proposal has not yet been provided

300$ USD în 5 zile
(119 Recenzii)

Hi, I hope you are doing well. I have experience with Load cell reading using Arduino as well as LCD display, I have read your project description and I would like to discuss it in more details. Looking Forwa Mai multe

315$ USD în 3 zile
(30 Recenzii)

Hello, My name is Prachya Suri from Thailand. I work for arduino at freelancer.com more than 2 year over 50 projects and all feedback from my customer is 5 stars. I can support you for your requirement. I have pre Mai multe

200$ USD în 14 zile
(29 Recenzii)

Hello, I am an Electronics and Embedded system developer. I have experience in Digital and Analog electronic design and Matlab. I well versed in Arduino hardware and software. Kindly check my profile. Reply me back and Mai multe

500$ USD în 7 zile
(36 Recenzii)

Hello, I am Anthony. I am working FULL TIME as freelancer. I have double degrees in Mechatronics and Applied Science fields. I have very good feedbacks on freelancer.com . Please check the lin Mai multe

200$ USD în 3 zile
(33 Recenzii)

hi i am an electrical engineer. i have vast experience related to circuit design and micro controller programming. i have done many embedded system projects. i have hardware experience load cell. let me know if you are Mai multe

350$ USD în 5 zile
(22 Recenzii)

Dear sir I have a good experience in Arduino and load cells Have an equippment for prototyping Also, I have an experience in creation of graphic interfaces for display with TFT touchscreen (the price is compar Mai multe

270$ USD în 15 zile
(28 Recenzii)

Dear Friend, We have good 5+ years experience in embedded software and design, It is not only our job but passion. We have worked on from basic hardware to quad-copters including custom apps, IoT's and PCB designs. Mai multe

270$ USD în 6 zile
(12 Recenzii)

Dear Sir, I have got all the hardware you need with 3 kinds of lcds . Here is my website [url removed, login to view] I provide services to local factories (mostly soyabean) and develop software on embed Mai multe

332$ USD în 3 zile
(2 Recenzii)

Hi! Im an electrical and electronic masters graduate of UWE. I have the experience of programming in C/C++/Assembly/Arduino/PIC C/MikroC/MATLAB for more than three years. I also have the knowledge and experience of EL Mai multe

250$ USD în 5 zile
(8 Recenzii)

Hello! I can help you! I have all the necessary equipment to carry out this project. I've had experience in writing firmware for these devices. But In fact, I need a more detailed description of the project.

250$ USD în 20 zile
(4 Recenzii)

Hi sir, We are team of expert engineers who are sound experienced in embedded systems (arduino + other microcontrollers), programming, circuit designs, electronics, product designs, pcb layouts, database management, Mai multe

160$ USD în 10 zile
(3 Recenzii)

FREELANCER RECOMMENDED ------------------------------------------------------ Can help... I am an Expert... Lets Start! Please start a Discussion with me and we can get started from there... Please check the past p Mai multe

1000$ USD în 10 zile
(6 Recenzii)

Thank you for reading this proposal . I'am an Electronics Engineer with professional experience of designing embedded systems with the process starting from circuit schematic design , Microcontroller / Microprocesso Mai multe

183$ USD în 8 zile
(5 Recenzii)

A proposal has not yet been provided

166$ USD în 30 zile
(0 Recenzii)

Hi, I am professional in this task.I would like to assist you in your projects. Get it done professionally get it done right the 1st time. I am here to make long term relationship. I would like to get all details from Mai multe

155$ USD în 3 zile
(0 Recenzii)

Hi! I'm an electrical engineer. I have worked on many projects with arduino from design of small circuitry to the design of autopilot for quadcopter. I have your complete set of requirements. I can surely do the cod Mai multe

120$ USD în 3 zile
(0 Recenzii)
222$ USD în 10 zile
(0 Recenzii)
150$ USD în 7 zile
(0 Recenzii)