Închis

MCU Project - Analog Signal Transmission ADC - DAC

Required: Circuit Scheme at Proteus or LTSpice, Keil Project file with CubeMx or MPLABX project file with libraries

Project Details: Basicly Master card Continuously Read 6 seperate ADC signal source and send their ADC information via Uart to Slave cards.

Addressable Slave Cards continuously receive analog information from the UART and Matched address Slave Cards convert them to 6 channel DAC.

Master Details;

A- Master card reads induvidual 6 channels ADC continually with DMA.

ADC Channels Resolutions:

1. And 2. Channel 12 bit resolution at +5v to -5v range

[login to view URL] [login to view URL] 8 bit resolution 0v to +5v range

B- Master Continuously reads 8 bit wide Dipswitch address while each ADC Conversion.

C- Master continuously send 10 byte frame to UART with DMA ( 1 byte start + 1 byte DipSWitch address data + 8 byte analog data )

Uart Speed 20MBit/s

D- Master MCU STM32 or PIC32 - LQFP Packages, 170 MHZ Processor speed or Over,

Slave Details;

A- Single MCU can not able to provide 6 Channel DAC so there should be 2 MCU Work Together to provide 6 channel DCA Output.

B- Addressable Slave Cards continuously receive analog information from the UART with DMA. Every UART FRame will be 10 byte long ( 1 byte start + 1 byte DipSWitch address data + 8 byte analog data) Uart Speed 20MBit/s

C- Slaves immediately Convert digital 8 byte Analog information to induvidual 6 channels DAC Output with DMA.

DAC Channels Resolutions:

1. And 2. Channel 12 bit resolution at +5v to -5v range

[login to view URL] [login to view URL] 8 bit resolution 0v to +5v range

D- 7 Seven segment display will show address, 2 button will adjust the address. Address will be save in the Eeprom.

Milestone of the project flowchart;

1- General flowchart presentation to show capability of the complate project

2- Proteus and LTSpice Project File ( We will help to create Opamp circuit for ADC and DCA )

3- Depends on the MCU Keil with CubeMX or MPLABX Project File include libraries.

Aptitudini: Electronică, Microcontroller, Design circuit , PCB Layout, STM32

Vezi mai multe: freelance mcu project, xilinx fpga adc dac, adc dac spartan, adc dac code vhdl spartan, adc dac spartan vhdl, adc dac board, fpga adc dac board, fpga adc dac, verilog code adc dac, adc dac altera, adc dac verilog, to build android project, which version of gradle is required?, to build android project, which version of gradle is required, mcu project goliath, analog front end adc, error running force:project:create: a name parameter is required to create a storage

Despre angajator:
( 1 părere ) istanbul, Turkey

ID Proiect: #31558331

18 freelanceri licitează în medie 733$ pentru acest proiect

avigupta0061

Best Analog Design Expert at your doorstep! Dear Client, We have already designed Various Analog Signal based Circuit so we will be a perfect fit to do this project for you. We can design Robust and reliable Circuit Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 2 zile
(39 recenzii)
7.3
(64 recenzii)
6.0
(48 recenzii)
5.5
bulgar

Dear Madame/M-r, We are a small R & D company, based in Bulgaria, Europe. We specialize in developing Embedded systems based ST(STM32), Microchip (Atmel )(PICs,AVR,Atmel ARM) and TI (MSP430) MCPUs and peripheries. For Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 10 zile
(14 recenzii)
6.1
HarimohanG

FREE OF COST CONSULTATION Dear Client, I can design Circuit at Proteus and LTSpice with Keil, CubeMx and MPLABX project file for you in a quality and timely manner. I have seen the Attachment you shared and read, unde Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 2 zile
(4 recenzii)
5.2
Devpro11

Hi, Dear client! *********************************************************** SHARING IDEAS AND INSPIRATIONS FOR YOUR PROJECT. PROVIDING A GOLDEN OPPORTUNITY TO RECEIVE THE BEST TECHNICAL SERVICE. ********************** Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(13 recenzii)
4.8
JaibhanSinghGaur

Hi,  I am a electronics and communication engineer with more than 2 years of experience in PCB and Circuit Designing. I have worked on many projects in past. Here are some software I have used for Circuit/Pcb Designi Mai multe

%bids___i_sum_sub_32%%project_currencyDetails_sign_sub_33% USD în 1 zi
(30 recenzii)
4.5
Adeel2k14

I hope you are fine. I am a senior electronics engineer. I have rich knowledge of embedded system design and PCB designing. I have understood the project description, i am 100% sure i can complete your task. I will p Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(13 recenzii)
4.4
sajjadtaghvaeifr

Hi, I hope you are doing fine. I have almost 3 years of experience in PCB design, Integrated circuits and VLSI. I have done many projects in Altium Designer. Also I'm expert in circuits analysis with Hspice and Pspice Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(5 recenzii)
4.6
phielectronicdes

We have extensive experience with STM32 microcontrollers in acquisition projects. Lets discuss your project in more detail at your earliest convenience. Find below a sample of previous work of our company on acquisiti Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 21 zile
(4 recenzii)
4.0
shateev20

Hi partievent. I have just read your requirements in detail and became interested in this project. As you can see my review, my specific skills are electronics and electrical engineering. I developed a digital relay Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 4 zile
(2 recenzii)
3.4
lechaantonov333

Hi! I'm interested in your project. I can help you with my skill and I have good experiences. I will finish it in time and do my best. Lets discuss more detail in private chat. Thanks for reading my bid.

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 3 zile
(2 recenzii)
2.9
hnutweblera

Hello.. I have read your project details and bidding now.. I have good experience with STM32, CubeMX, and Keil/IAR platform. Before I have worked for embedded programming, so can Help you. Hope more discuss with you. T Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 20 zile
(1 părere)
2.3
DenisSoldatov

Hello. I am an expert for Embedded System Design. I have experience developing ADC and DAC with STM32 and PIC32. I have all knowledges and experience what you need(including DMA, UART). I have developed a data-logger Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(2 recenzii)
2.0
SamCoff

Hi, I'm interested in your project. Please send me a message so that we can discuss more. I have an experience in STM32 platform and Schematic, PCB and firmware design. Regards

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 21 zile
(0 recenzii)
0.0
(0 recenzii)
0.0
gpnk1526

I would like to introduce my company Chola Design Solutions. we are into PCB & Mechanical Design Services. We have 5+ Years experienced Team. Kindly go through my company profile [login to view URL] Projects Mai multe

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(0 recenzii)
0.0
HoangTran2301

I have seen your algorithm, in the transmission frame of UART you only need 3 bytes 345 to store 12B CH1 and 12B ch2, bit 10 you can use it to calculate CRC code. If you need optimal solutions, please contact me

%bids___i_sum_sub_35%%project_currencyDetails_sign_sub_36% USD în 7 zile
(0 recenzii)
0.0