
Open
Posted
•
Ends in 6 days
Paid on delivery
I need a production-ready USB dongle that can sit in any laptop or desktop port and act as the single receiver for a fleet of wearable Collector Kits. The core requirements are: • Frequency: the RF front-end must operate on 868 MHz or 915 MHz so the same board can be stuffed for either region. • Power: the board is strictly bus-powered; no external barrel jack or battery input. • Capacity: it has to listen to, and reliably demodulate, traffic from roughly 25 simultaneous Collector Kits before forwarding the raw payloads to the host over a simple USB-CDC (UART) stream. This is a ground-up, chip-level design. Place the transceiver IC, MCU/USB bridge, matching network, crystal, ESD protection, and supporting passives directly on the PCB—no breakout modules or dev boards. Careful RF layout, impedance control, and enclosure clearance are essential to keep the finished stick compact and professional, similar in size to a commercial Wi-Fi dongle. Deliverables 1. KiCad Schematic, Optimised 1- or 2-layer PCB layout with manufacturing notes 2. Complete production files BOM with sourcing links, Gerber/ODB++ files, pick-and-place, and assembly drawing 3. Assist in ordering in the manufacturer's portal (JLCPCB, PCBWay, etc.) for 5 samples. 4. Technical documentation I will handle regulatory certification later, but please keep ETSI/FCC guidelines in mind during the design so we are not forced into major re-spins. If you have prior LoRa RF experience and can quickly turn a neat, manufacturable USB stick, let’s talk.
Project ID: 40803234
9 proposals
Open for bidding
Remote project
Active 7 secs ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
9 freelancers are bidding on average $150 CAD for this job

Hello, Designing a compact, production-ready LoRa USB receiver is a strong match for my 10+ years of electronics and PCB design experience, including wireless communication, LoRaWAN, embedded systems, and complete hardware product development. I can handle the ground-up schematic, direct chip-level component selection, RF matching network, MCU/USB interface, crystal, ESD protection, bus-powered supply, and compact PCB layout without relying on breakout modules. My experience includes STM32, ESP32, AVR/ATmega, UART, low-power electronics, multilayer PCB design, component libraries, DFM, prototyping, testing, troubleshooting, and small-batch production. I can also prepare the BOM, sourcing information, Gerber/ODB++ files, pick-and-place data, assembly drawings, manufacturing notes, and technical documentation, while keeping 868/915 MHz flexibility and ETSI/FCC-oriented RF practices in mind. I am ready to develop a neat, manufacturable LoRa receiver dongle and support the initial five-unit production order through the manufacturer’s portal. Thanks!
$155 CAD in 5 days
5.7
5.7

Hi there, What LoRa modem or RF chip do you prefer for the 868/915 MHz build, and do you want a single PCB with region-specific component options? How should the USB-CDC stream frame packets and report RSSI or CRC status for the host app? The main challenge is packing a clean RF section, USB power, and a stable digital path into a very small dongle. A practical approach is a chip-level design in KiCad with a bus-powered USB interface, low-noise 3.3 V regulation, controlled-impedance RF routing, selectable matching for 868 or 915 MHz, and ESD protection at the connector. The biggest risk is receiver sensitivity loss from layout, grounding, or enclosure coupling. That can be reduced with a short RF path, solid return paths, careful crystal placement, and early review of antenna or connector keepout so the board stays compact without sacrificing performance. For production, the work can include schematic, DRC-clean 1 or 2 layer layout, BOM with sourced parts, fab and assembly files, and notes for JLCPCB or PCBWay ordering. Validation against the target band and a first sample spin check would keep the design close to ETSI/FCC-friendly practice from the start, and I can help prepare the technical docs too. Best, Hlib
$155 CAD in 5 days
2.4
2.4

Hi, I can help you develop a compact, production-ready USB LoRa receiver from the ground up. I have experience with PCB design, embedded electronics, KiCad, component selection, and manufacturing-ready layouts. For this design, I would focus on selecting the right RF architecture to reliably handle 25 Collector Kits, rather than relying on a basic single-channel transceiver. I can handle the complete schematic, RF matching network, MCU/USB-CDC interface, ESD protection, and compact PCB layout. The design will support 868/915 MHz through region-specific component stuffing, with careful attention to RF impedance, grounding, and antenna clearance. I will also prepare the complete BOM, Gerbers, pick-and-place, assembly drawings, and technical documentation. Before finalizing the architecture, I would like to confirm the Collector Kits' LoRa protocol and whether the 25 devices transmit simultaneously or use scheduled transmissions. I can also assist with the manufacturer's portal and ordering the first five prototypes. Best regards, Engr. Muhammad Uzair
$99 CAD in 6 days
1.9
1.9

Hello, My electrical engineering background is best suited to producing clear, manufacturable electrical documentation and coordinated design packages, but I want to be transparent: my profile does not show prior LoRa, RF, USB-dongle, KiCad, or embedded PCB experience. I do offer experience across electrical system layout, multidisciplinary coordination, code compliance, technical drawing production, and detailed engineering review. That can support documentation quality, design coordination, and practical manufacturing notes; however, the RF transceiver selection, 868/915 MHz matching network, impedance-controlled layout, USB-CDC implementation, and production validation should be handled by a specialist with demonstrated RF/LoRa PCB experience. If you need an electrical engineering professional for the documentation, review, and coordination aspects of this project, I would be glad to contribute honestly and carefully. Thanks!
$30 CAD in 3 days
0.6
0.6

A single-chip SX126x-class transceiver with a small USB MCU is the usual way to build this, and it fits a 2-layer board if the RF section is kept tight. I'll design the schematic and layout in KiCad with the 868/915 MHz matching network, a proper ground pour and ESD protection on the USB lines. You'll get production files, BOM, pick-and-place and notes, and I'll help place the 5-sample order. Delivery in about a week. Some of my RF and wireless node boards are in my portfolio. Do you already have a preferred LoRa chip or antenna type?
$150 CAD in 7 days
0.5
0.5

Hello, My Electrical Engineering background and experience with SolidWorks and Fusion 360 provide a strong foundation for creating a compact, manufacturable USB dongle enclosure and supporting engineering documentation. I can develop clear production drawings and coordinate the board’s physical integration, USB-port clearance, enclosure fit, mounting details, and manufacturing documentation. My broader engineering experience includes electrical power and lighting layouts, MEP coordination, CAD drafting, and construction documentation, with familiarity across NEC and NFPA requirements. I can also prepare organized technical files and assist with manufacturer-facing documentation for sample production. The profile does not specifically demonstrate LoRa transceiver, RF matching-network, or KiCad PCB-layout experience, so I would not overstate that specialty. However, I offer disciplined electrical engineering, CAD, and documentation skills suited to the mechanical and production-support aspects of this project. I would be glad to contribute to a professional, manufacturable dongle design. Thanks!
$150 CAD in 2 days
0.0
0.0

Hello, My background is in software and AI product development, not chip-level RF or PCB engineering, so I cannot honestly claim prior LoRa receiver, KiCad, RF layout, or production electronics experience for this USB dongle. My listed skill is prototyping, supported by 8 years of experience building production-ready software, SaaS platforms, APIs, and integrations. I could contribute to the host-side USB-CDC handling, raw payload ingestion, backend integration, documentation, or a companion application, but the transceiver selection, 868/915 MHz matching network, impedance-controlled layout, EMC considerations, BOM, and manufacturing files require a dedicated RF/PCB specialist. For the hardware design itself, I recommend selecting a freelancer with demonstrated LoRa, KiCad, USB device, and RF production experience. If your project also needs the software layer that receives and processes the dongle’s payload stream, I would be glad to contribute there. Thanks!
$140 CAD in 2 days
0.0
0.0

Edmundston, Canada
Payment method verified
Member since Jan 24, 2026
$250-750 CAD
$150-200 USD
₹1500-12500 INR
₹1500-12500 INR
$3-10 NZD / hour
$10-30 USD
₹250000-500000 INR
$750-1500 USD
₹1500-12500 INR
$30-250 USD
$15-25 USD / hour
₹1500-12500 INR
$750-1500 USD
₹1500-12500 INR
$250-750 AUD
$10-50 USD
£1500-3000 GBP
$1500-3000 USD
₹1500-12500 INR
$10-300000 USD
₹600-1500 INR